Table of Contents
The basic rule for garage receptacles is that one receptacle outlet needs to be installed in each vehicle bay and not more than 5 ½ feet above the floor.
How many outlets are needed in a garage?
Garages must have at least one receptacle, including one for each car space. All garage receptacles must be GFCI-protected.
How many outlets can be on one circuit in a garage?
The answer to the question how many outlets on a 20 amp circuit is ten outlets. Always comply with the 80% circuit and breaker load rule, allowing a maximum load of 1.5 amps per receptacle.
Where should outlets be placed in a garage?
Many contractors place outlets 12 to 18 inches above the floor because that height suits most people, not because the NEC demands it. That being said, the American Disabilities Act expects homeowners to place wall receptacles at least 15 inches above the floor.
Does a garage need 20 amp outlets?
Code Change Summary: A new code section was added to require a 20 amp circuit for a dwelling unit garage. For those that do, whether attached or detached, if the garage is supplied with electric power, at least one 120-volt, 20-ampere branch circuit must be installed to supply garage receptacle outlets.
How many outlets do I need for a 2 car garage?
However, the code is just a minimum set of installation rules. The basic rule for garage receptacles is that one receptacle outlet needs to be installed in each vehicle bay and not more than 5 ½ feet above the floor.
How many outlets can be on a 30 amp circuit in a garage?
20 outlets for 30 amp breaker as a rule of thumb of 1.5 amps per outlet.
How many outlets can run off GFCI?
There’s no limit. A standard GFCI will protect up to 20 amps, drawn from any combination of receptacles, either the built-in one or any number of additional ones connected to its load terminals.
How many GFCI outlets do I need in my garage?
Yes, all garage outlets must be GFCI-protected-no exceptions. Since 2008, GFCI outlets have been required for “all 125-volt, single-phase, 15 and 20-amp outlets” in the garage.
How many outlets can be on a 15 amp breaker?
Technically, you can have as many outlets on a 15 amp circuit breaker as you want. However, a good rule of thumb is 1 outlet per 1.5 amps, up to 80% of the capacity of the circuit breaker. Therefore, we would suggest a maximum of 8 outlets for a 15 amp circuit.
What is code for garage wiring?
The code requires that you hold all wires at least 1-1/4 in. (Photo 1) from the back and front surface of studs and joists. With 2×4 framing, that means you have to hold two cables running side by side tight to each other.
Is 15 amp enough for garage?
As a general guideline, you’d use 12 AWG copper conductors with a 20 ampere breaker, and 14 AWG copper conductors with a 15 ampere breaker. Since the receptacles are in a garage, they’ll have to be GFCI protected. This protection can be provided by a GFCI receptacle, or a GFCI breaker.
Do you need GFCI outlets in the garage?
GFCI protection is required for 125-volt to 250-volt receptacles supplied by single-phase branch circuits rated 150 volts or less to the ground. GFCI receptacles are required in bathrooms, garages, crawl spaces, basements, laundry rooms and areas where a water source is present.
How far apart should outlets be in a shop?
The maximum spacing between receptacles, according to the National Electric Code (NEC), has been set at 12-feet since 1956–with no point along a wall being more than 6-feet from a receptacle.
Can garage lights and outlets be on same circuit?
But of course they can. Very stupid to do so, and it may not pass the electrical code, but yes it ‘can. ‘ The reason it is stupid though, is that if you for some reason trip the breaker [or blow a fuse, whatever] you will loose electrical to the outlets and the lights.
Can 12 gauge handle 30 amps?
You should not use a 30-amp circuit breaker on a 12-gauge wire. The circuit breaker installed on a circuit is of a specific size to protect a certain wire gauge. This higher current can damage the thinner wire, melt the insulation, cause short circuits, fire, and even lethal shock.
Is 50 amp enough for garage?
A 100-amp subpanel in a detached garage may be enough to handle high-draw appliances such as refrigerators. As for basic lighting or low-load electronic devices, a 50- or 60-amp subpanel in a detached garage may suffice.
Will a 12 2 wire carry 30 amps?
Can You Use a 12-2 AWG for 30 Amps Circuit. Yes, based on the National Electric Code or NEC, you can use 12-2 AWG cables for THHN or THWN-rated wires. These cables are made for general purposes and can hold up to 194 degrees without taking any damage.
Can you have 2 GFCI outlets on the same circuit?
Yes, you can have many GFCI outlets on the same circuit The way they vary from a regular outlet is they check for ground faults.
How many GFCI Can you daisy chain?
You can simply install one GFCI and daisy chain any legal number of regular grounded outlets off the LOAD terminals (not the line terminals! Those go to the supply from the panel) off of it, and it will protect them all. There is no need to use further GFCI outlets in that circuit.
Can you wire GFCI outlets in series?
But we can also wire them in series. However, when there is some type of load exists then there is a possibility that we may not be unable to get correct values of voltages at the other outlets of our application, having a series connection of GFCI. So always try to connect GFCI outlets in parallel.
