Table of Contents
Lighting with No Igniter Take a long lighter to reach the pilot. Remove the plate attached below the dial box. Switch Pilot to OFF. Wait for a while, – 5-10 minutes until there won’t be any gas. Change the temperature to LOW, and switch to Pilot. Push ON/OFF dial down, and simultaneously use the lighter.
Can you manually light a water heater with electronic ignition?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.
Can you manually light a gas hot water heater?
Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem. If you’ve moved into an older house, though, you many have the kind of water heater that needs to be lit manually.
How do you light an electric hot water heater?
Lighting A Hot Water Heater Pilot Light Set the temperature control. to its lowest setting. Set the on-off control. to the pilot setting. Press the hot water heater. pilot button down and. hold it. While looking through the the sight glass slowly press the spark generator until you here it click. You should see a spark.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Why does my water heater not stay lit?
Thermocouple Issues If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
Do hot water heaters have pilot lights?
There’s no gas or pilot light involved in electric water heaters. If the power to your electric water heater is off, you may have an electrical issue requiring professional assistance.
Can you light a pilot light with a lighter?
Fortunately, relighting a pilot light is easy. All you need is a long-neck multipurpose lighter and a flashlight. NOTE: Never relight the pilot if you smell gas. This indicates a leak and could cause an explosion if you light a match or lighter.
How do you light a pilot light on a water heater?
Find and Light the Pilot Open the access cover and locate the pilot, which should be protruding from the control valve. Grab the wand lighter and depress the gas valve. Then, with the valve still depressed, light the pilot. Continue holding down the gas valve for about 20-30 seconds, then release it.
Do electric heaters have a pilot light?
Electric furnaces have pilot lights, the same as gas furnaces. The trend of replacing pilot lights with electronic ignition systems in electric furnaces was similar to the one happening in gas furnaces. That means that before about 2010, most of the electric furnaces with pilot lights were produced.
Does an electric water heater need to be lit?
Whether you have an electric water heater or a gas water heater, you can turn it on without having to call a professional to help you. An electric water heater requires finding the circuit breaker and turning it on, while a gas water heater needs the pilot light to be lit.
Why would pilot light go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
Why is my gas heater not lighting?
There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
How do you light a pilot light?
If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.
What happens when water heater pilot light goes out?
If the pilot light goes out, your water heater won’t be able to ignite the gas burner and therefore, won’t be able to heat the water. But once the pilot light is relit, the water heater is able to ignite the gas burner and can begin to heat the water again.
Where is the igniter button on a water heater?
The spark is small, and the igniter is deep inside the base of the water heater. You may have to dim the room lights to see the spark. If you still can’t see a spark, turn the gas control knob OFF, turn the gas supply valve OFF, and click on “More Help” below.
