Table of Contents
The Sweet Spot – Most people agree that 3/16” is a good gap between boards. Going more than a ¼” may get a little too wide. The width of a nail head is just about right. Treated Lumber – Usually treated lumber will have some shrinkage so you can butt the boards almost right against each other during installation.
How far apart should deck boards be?
Proper wood deck board spacing should have at least a 1/8 inch gap after the decking has dried out. If you install your wood or treated deck boards while they are still wet boards, then they should be attached without a gap between them.
Should you space treated deck boards?
Leave a gap between pressure treated deck boards when the wood is wet. Leave Gap: If the pressure treated wood has been kiln dried after treatment (KDAT), leave a 1/8” gap (the thickness of an 8-penny nail) between the boards when attaching, since the wood will expand slightly over time.
Should deck boards be butted together?
We recommend butting treated deck boards together because as the moisture dries from the wood, the boards will shrink and naturally form gaps to allow water drainage. (Depending on moisture content, cedar, cypress and especially hardwood decking may require deliberate spacing for consistent joint sizes.)Jun 21, 2010.
How do you layout deck boards?
Deck boards should sit 1 ½” off the edge of each side of your deck. Use your straightest deck board and lay it first across the deck’s front edge, opposite your house. Each board should have a ⅛” gap. All deck board should end on a joist, making sure to stagger deck board ends.
How far apart are joists for a deck?
Step 4: Make Sure Your Joists Are Spaced Correctly Deck joist spacing should never exceed 16″ on center (with the exception of MAX deck boards, which allow for maximum 24″ on center). For a more rigid feel, 12″ or less may be preferred.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
Do deck boards shrink or expand?
Any type of decking board will expand and shrink, whether it’s wood, plastic, or composites. However, they don’t change in size as much as wood or plastic. Wood fibres hold the shape when the composite undergoes thermal expansion, while the plastic fibres do the same when moisture is involved.
Should I Space 5 4 decking?
For 5/4 pressure treated decking, it should be installed tight and allowed to shrink to provide water drainage. With cedar 5/4 decking installation should be with 1/16″-1/8″ gap (2-3mm), which will expand to 1/8-1/4″ (3-6mm) once the wood has dried. Providing both deckings’ plenty of spacing for drainage.
Where do you start laying deck boards?
In most cases, it’s best to start with a full board on the outside edge of the deck and work toward the house so the odd board is less visible. Then measure when you’re 4 to 5 ft. away from the house and adjust the gap sizes to be sure the last board is a consistent width.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
Do you have to stagger deck boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Should deck boards run parallel house?
The default direction decking runs on an attached deck is parallel with the house. A few reasons for this are deck framing construction, water runoff and appearance. Decking running parallel to the house is beneficial structurally, aesthetically and costwise.
Should you flip deck boards?
They are treated lumber.” You bet you can flip them. There’s no harm in doing so. While you’re at it, be sure to clean off any debris from the top of the support joists and check for rot at those locations.
Which direction should decking boards run?
Laying decking boards in a diagonal direction gives the deck a very noticeable look. To lay a deck this way, joist have to be set no wider than 300mm apart, so you may need one or two more joists extra.
How many joists do I need for a 12×12 deck?
For example, a 12-foot x 12-foot deck of 5/4 x 6 pressure treated wood decking on 16 inches on center spacing of joists will require: A 12-foot long deck with joists 16 inches on center will require 10 joists.
Are 2×6 strong enough for deck joists?
For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. Most decking is not strong enough to support longer spans than 16″.
How far can a 2×8 joist span without support?
A rule of thumb is 1.5 times a joist’s depth but in feet when spaced at 16” centers. In general, a 2×8 will span 1.5 x 8, so 12-feet.
