QA

Quick Answer: How To Start A Briggs And Stratton Lawn Mower

Sit on the seat of the mower. Depress the clutch/brake pedal, and engage the parking brake. Move the blade lever to the disengaged position; set the throttle to fast, and move the choke to the full choke position. Insert the key, and turn it to crank the engine.

Why will my Briggs and Stratton engine not start?

Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

How do you start a lawn mower step by step?

Step 1: Position the lawn mower. Step 2: Check the petrol level. Step 3: Check the oil level. Step 4: Check the spark plug. Step 5: Press the fuel button 3 to 5 times. Step 6: Put the throttle in the start position. Step 7: Pull the starter rope. Step 8: Lawn mowing!.

How do you start a Craftsman Briggs and Stratton push mower?

In case your Briggs & Stratton lawnmower has a horizontal lever around the handle, one must firmly grip the handle while the lever rests against it. Now, firmly grip the handle meant for starting, attached at the end of the rope. Pull it firmly and repeat this step until the motor starts up.

How do you start a lawn mower that won’t start?

If you run into problems getting your lawnmower ready for spring, try the following: Use fresh gas. Old gasoline can cause starting difficulties. Check the spark plug. Use the choke. Prime the mower. Check the air filter. Check the cables. Check for water in the fuel tank. Clear the starter cord of blockages.

How do you start a lawn mower with one pull?

To start your lawn mower in one pull, stand behind the mower and pull the chord straight towards you as hard as you can. Ensure your mower has gas in it. Your mower also needs to have clean oil and a clean air filter too. Being able to start your lawn mower in one pull requires you to maintain your lawn mower properly.

Where is the primer bulb on a Briggs and Stratton?

The primer bulb on a Briggs and Stratton 5 horsepower engine is located on the back of the air filter assembly next to the carburetor. It’s a small rubber button-like part that the user must press to start the fuel flow from the gas tank into the carburetor.

What is the easiest starting lawn mower?

Easy Start Lawn Mowers Troy Bilt TB220. Snapper P2185020. Husqvarna 22 Inch Self Propelled. Lawn-Boy 17734. Mowox Self Propelled Electric Start Lawn Mower. Ryobi 20″ RY40190. Oneinmil Electric Lawn Mower Self Propelled. GreenWorks 25142 Corded Lawn Mower.

How do I start my Craftsman lawn mower?

Hold onto the recoil starter handle located on the right hand side of the mower and slowly pull the rope. Allow the rope to rewind gently. Pull the recoil rope rapidly using a complete, full-arm motion before letting the rope return gently. Repeat pulling the rope rapidly and returning until the lawn mower starts.

How do you start a Craftsman riding lawn mower?

Starting Step 1: Place the key in the ignition switch. Step 2: Disengage the PTO by setting the lever to the PTO OFF position. Step 3: Set the parking brake. Step 4: Activate the choke. Step 5: Turn the key to START. Step 6: Set the throttle/choke control to FAST before you start mowing.

How do you turn off a Briggs and Stratton lawn mower?

All lawn mowers can quickly be shut off. Stop pushing the lawn mower. Make sure you are standing still and the mower is on level ground. Pull the throttle to the “Stop” position. Locate the spark plug wire on the lawn mower. It should travel from the throttle to the motor.

Why is it so hard to start my lawn mower?

The fuel filter might be clogged. A clogged fuel filter is most commonly caused by leaving old fuel in the lawn mower. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and make the engine hard to start.

How do you prime a lawn mower without a primer bulb?

How to Prime a Lawnmower without Primer, step by step Step 1: Preparation of the lawnmower. Step 2: Locate the primer bulb near the carburetor. Step 3: Locate the air filter near the engine. Step 4: Remove the air filter gently and make sure not to damage it.

Where is the spark plug on a lawnmower?

Spark plugs are typically located on the back or side of a lawn mower engine. Look for a short wire that’s about 1/4-in. -thick leading to the top of a short, cylindrical protrusion from the engine. If you’re not sure where the spark plug is, consult your owner’s manual.

Why does my lawn mower not start when warm?

Air leaks cause an engine to pull in too much outside air, which throws off the gasoline-to-air ratio. As the engine heats, parts expand, and all tiny gaps become larger. The result is a poorly running engine and one that eventually stops. Loose bolts are a common culprit in a mower engine that shuts down when hot.

How do you know if the choke is on or off?

The “choke” is off when the choke lever is down or when the choke lever is facing you if your choke is a handle bar mount. Choke off means that the choke plate is not covering the carb throat.