Table of Contents
How to Measure for Landscape Rock Measure the width of the area. Measure the length of the area. Multiply the width by the length. Figure out the depth of your layer of rock. Convert the depth measurement from inches to feet. Calculate cubic feet of the area. Purchase enough landscape rock to cover the area.
How do I calculate how much rock I need?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How do I calculate how much landscape rock I need?
The landscape rock formula is as follows: (Length x width x depth) / 27. Sand 1.10 – 1.25 tons (2,200 – 2,500 lb.) Landscape Gravels 1.20 – 1.35 tons (2,400 – 2,700 lb.) Washed Gravel 1.35 tons (2,700 lb.) Washed Limestone 1.20 tons (2,400 lb.) Limestone Base 1.35 tons (2,700 lb.).
How many yards of stone do I need calculator?
Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This number is how many cubic yards of crushed stone you need.
How do you measure a landscape stone?
Rectangle Measure Length and Width (in feet) Length x Width = square feet. Determine desired depth of material (see recommended depths and chart below) Square feet divided by sq. Example: A rectangular area 16 feet long by 10 feet wide and you want 4 inches deep of stone. Calculations: 16 x 10 = 160 square feet.
How many square feet does a ton of river rock cover?
One (1) ton of river rock covers approximately a 50-75 sq. ft. area. This river rock ranges from 4 in. to 10 in.
How do you measure the size of a rock?
Measuring for rock is fairly straightforward and can be done with a long tape measure. To make this task easier, enlist the help of a friend to hold one end of the tape while you measure and record the length and width of the area in feet. Then, multiply these two numbers to find the square footage.
How deep should rock be for landscaping?
For most purposes, 2 inches (or 50mm) of landscaping rock is adequate. If you use a material that is larger than this, then the depth will be the same size as the rocks themselves. That is, you will want one layer of 3 to 8 inches (75 to 200mm) of rocks.
How much rock do I need per square foot?
How much landscaping rock do I need? Material Suggested Depth Coverage Area per 1 ton 3”-8” rock 3”-8” 60 square feet 1”-3” rock 1”-3” 80 square feet 3/4”-1” screened gravel 2” 100 square feet 5/8”-1/2” screened gravel 2” 120 square feet.
How many square feet will 5 tons of gravel cover?
Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.
What size river rock is best for landscaping?
3/4 Inch to 2 Inch River Rocks Since smooth rocks are often used to mulch flowerbeds and line garden pathways, larger, heavier gravel is less likely to scatter. If you’re creating a pathway or other more decorative garden element, medium-sized river rocks might be the perfect choice!Jan 14, 2019.
How many square feet does a yard of rock cover?
How Much Does A Yard Cover? A cubic yard of material can be spread to cover 100 square feet (10×10 foot area) at 3 inches of depth.
How much 2b Stone do I need?
Calculate 2B Limestone Coverage (Square feet) 400 sq ft Volume (Cubic yards) 2.5 cu yd Estimated amount (Pounds) 5,951 lb Estimated amount (Tons) 2.98 ton Amount +15% compression 3.42 ton.
How much does a yard of river rock weigh?
River rock weighs about 2,600 pounds or 1.3 tons per cubic yard.
How do you measure for landscaping gravel?
How much gravel do I need? Determine the length and width of a cuboidal excavation. Calculate the area of the excavation, multiplying the length and width together. Determine the depth of the excavation. Multiply the area and depth of the excavation to obtain its volume in cubic yards: 18 * 2 = 36 yd³ .
What area does a ton of gravel cover?
Type 3 Aggregate Calculator Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.
How thick should you lay River rock?
The suggested depth of coverage varies according to the size of the individual stones. If the stone size is 1/2-inch or less, the suggested depth is 2-inches. Stones that are 3/4-inch to 1-inch should have a depth of about 3-inches. Stones that are 1-inch or larger should have a depth of 4-inches.
How big is a 1 ton rock?
How big is a 1 ton rock? Assuming an average weight of 165 pounds per cubic foot, a 1 ton rock has a volume of 12.1 cubic feet, a diameter of 2.85 feet, and a circumference of 9 feet.
Should I put plastic under River rock?
The plastic is only recommended for small areas of rock, not for mulched beds, graded slopes or hillsides. If you have Oaks be wary of placing rocks beneath the trees as Oak leaves do not break down quickly and you will have to blow or vacuum the leaves from the rocks to keep them looking neat.
How much does a 3 foot diameter rock weigh?
How much does a 3-foot boulder weigh? A sandstone boulder typically weighs about 150 pounds per cubic foot. That means that a round boulder that is 3 feet in diameter, or 27 cubic feet, weighs about 4,300 pounds. Limestone and granite are a bit heavier at 175 pounds per cubic foot.
