Table of Contents
What are the signs of a bad ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
How hard is it to replace a ballast in a fluorescent light?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
How do you know if it’s the bulb or ballast?
Take out your current bulbs and replace them with the new bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
Why do new fluorescent lights flicker?
Lamp blinks: This is usually because of a poor connection where the tube fits into its sockets at each end. Take the tube out and clean the pins at each end with fine steel wool. Brush dust out of sockets, then reseat firmly.
What happens if you wire a ballast wrong?
The ballast is wired to the home’s hot, neutral and ground wires on one end, and to the light fixture’s lamp holders on the other end. If a ballast fails, it can cause a short, burn out tubes or even cause a fire, so it must be replaced.
Can you repair a ballast?
While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.
Is it cheaper to replace ballast or fixture?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
How long do fluorescent ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
What is the black stuff in a ballast?
The black goo leaking from the ballast is potting material that acts as a dielectric insulator and prevents the internal components of the ballast from arcing, while also eliminating the heat and noise produced by the core (transformer) that regulates the ballast’s output voltage to the lamps.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
What causes a ballast to go bad?
Every ballast has an ambient operating temperature range and UL location rating. When it’s too hot or too cold, the ballast can burn or fail to start your lamps at all. Heat combined with prolonged condensation inside an electronic ballast can cause corrosion and ballast failure.
Why does my fluorescent light work sometimes?
If a fluorescent tube blinks on and off-a slower and more distinct process than flickering-the fault may lie in loose wiring or in another component, called the ballast. The ballast is almost always to blame if the fixture hums during operation.
Why is my fluorescent light not working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
Why do fluorescent lights not turn on sometimes?
If you find your fluorescent light won’t turn on sometimes, there could be a variety of reasons why. It could be as simple as needing to replace the bulb or plug the light itself in; or, it could be something more serious, such as a blown fuse or a damaged/dying starter.
Where is the ballast on a fluorescent light fixture?
Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
