Table of Contents
Does the drip edge go over or under the felt?
1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Should drip edge be tight against fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
Does drip edge go over ice and water shield?
(The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.) You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing.
Where should drip edge be installed?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Does roofing paper go on before drip edge?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
How far should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Do you nail drip edge to fascia?
You don’t. The drip edge is attached onto the plywood roof decking before any shingles are installed. And assuming that the roof’s bottom edge has a typical fascia trim, that trim should be in place before the drip edge.
Can you install drip edge after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Do I need a drip edge on my roof?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Do you nail down ice and water shield?
If necessary, WaterGuard Rain & Ice can be nailed in place with fasteners or the adhesive activated by heat welding. If WaterGuard Rain & Ice is not used on the entire roof, other underlayments should be lapped 6″ onto WaterGuard Rain & Ice applications (like roof valleys).
Do gutters need to be removed to install drip edge?
It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.
Do you put drip edge on gable ends?
Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
How far should shingles hang over drip edge?
Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.
Do you need drip edge on roof?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Where do you put drip edge?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Should drip edge go over or under felt?
Does Drip Edge Go Over or Under Felt? According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof.
