Table of Contents
What causes a pilot light to go out on a water heater?
Your thermocouple senses when your pilot light is burning. If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Can I replace a thermocouple myself?
1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.
Does gas leak if pilot light goes out?
When the pilot light goes out, it does not leak carbon monoxide gas. Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds.
Can I relight my hot water heater?
If your heater’s pilot goes out, you can relight it yourself. Turn the gas regulator valve’s knob to “Pilot,” press down on it and hold it down. This starts the flow of gas to the pilot burner. On some water heater models, you press and hold down a separate red button to start the pilot burner gas flow.
How do I know if my pilot light is out?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
How do I know if my thermocouple is broken?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
Can you manually light a gas water heater?
Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem. If you’ve moved into an older house, though, you many have the kind of water heater that needs to be lit manually.
How much should a plumber charge to replace a thermocouple?
Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.
How much does a thermocouple cost?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on.
How long do thermocouples last?
How to Tell if You Have a Bad Thermocouple? Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
Is it safe to relight a pilot light?
But first, some words of caution: –Don’t relight the pilot light if there is a strong gas odor. Close the main gas shut-off valve for your house or for the appliance with the leak and call the gas company immediately. Get everyone out of the house until the problem is corrected by gas company technicians.
Should my pilot light always be on?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
How can I tell if my water heater pilot light is on?
It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.
