QA

How To Fix A Propane Heater

How do you fix a propane heater that won’t stay lit?

If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.

What causes a propane heater not to light?

The most common reasons for a non-working propane heater are a dirty thermocouple, a thermocouple that is too far from the flame, a blocked pilot tube, an empty/overfilled gas canister, and drafts. Fortunately, the majority of homeowners will be able to take care of these issues on their own.

How do you unclog a propane heater?

Make sure the propane heater is turned off. Vacuum as much dust and debris as you can from the outside of the heater, and vacuum inside the vent holes and grids on the heater. Use a small paint brush for brushing dust away in tight areas. Gently move the brush over the igniter and the flame areas on the heater.

Why does my propane heater flare up?

When you turn up a heater’s thermostat, it sends a tiny electrical signal to the gas valve, prompting it to open and send gas to the burner, where the pilot ignites it. Most heater malfunctions can be traced to a faulty pilot, and that, in turn, may be due to a clogged gas pipe.

How do you fix a pilot light on a gas heater?

Gas Heater Pilot Light Troubleshooting Check the Thermocouple. If your pilot light won’t stay alight, it might be the thermocouple. Adjust an Irregular Flame. If your pilot light is flickering and faint, you might need to adjust the flame. Check the Gas Levels. Check for a Corroded Pilot Tip. Regulate any Draft.

Why is my furnace not running?

Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.

Why does the pilot light go out on my wall heater?

If your furnace pilot light keeps going out, it’s likely you have a broken thermocouple in your gas furnace. The thermocouple is a rod that comes into physical contact with the flame in your system. When this component is not able to detect the flame, it will close the gas valve to prevent a gas leak in your home.

How do you clear a pilot tube obstruction?

How to Fix a Plugged Pilot Hole on a Water Heater Remove the cover plate at the bottom of the water heater. Turn the gas control to the “Off” position. Locate the pilot tube. Clean the pilot hole by brushing it with a stiff wire brush. Screw the bracket back onto the valve and turn on the gas.

How do you jump a thermocouple?

To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.

Can I clean a thermocouple?

Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.

Why does my gas outdoor heater keep turning off?

One common issue that patio heater owners face is keeping their patio heater lit. The typical cause for this is that the pilot light flame has become too far away from the thermocouple. Thus, the thermocouple will turn off the patio heater as it tricks the gas value in to thinking that the pilot light is out.

Why won’t my gas heater light up?

There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.

How do I fix my pilot light?

Relight the pilot light. Turn the knob to “Pilot,” and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light’s opening. Keep the reset switch depressed until the pilot light is burning steadily.

What happens when pilot light goes out?

If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.