Table of Contents
What are the signs of a bad ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
Can a fluorescent light ballast be repaired?
If you can change out a light switch or outlet you can definitely replace an old ballast that doesn’t work. As I said in the beginning, you’ll save yourself $75 to $90 doing this fix yourself.
Can a ballast be repaired?
While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
How do you change a ballast in a fluorescent light fixture?
Instructions Remove the Cover. Remove the lens, or diffuser cover, from the fixture. Remove the Fluorescent Tubes. Remove the light bulbs (fluorescent tubes). Remove the Cover Plate. Disconnect the Ballast Wires. Remove the Ballast. Prepare the Wires. Mount the New Ballast. Dispose of the Old Ballast.
How do you know if it’s the bulb or ballast?
Take out your current bulbs and replace them with the new bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Is it easy to replace a ballast?
You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How much does it cost to replace a ballast?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Why did my ballast stopped working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
Why does my fluorescent light keep burning out?
Turning a light bulb on sends a jolt of electricity through the filaments, which is more likely to break it than a continued current—that’s why light bulbs often burn out as you turn them on. If you turn lights on and off frequently, you’re likely reducing the lifespan of the bulb.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
What happens if you wire a ballast wrong?
The ballast is wired to the home’s hot, neutral and ground wires on one end, and to the light fixture’s lamp holders on the other end. If a ballast fails, it can cause a short, burn out tubes or even cause a fire, so it must be replaced.
How is a ballast wired?
Usually hidden from view, the ballast is installed inside an overhead fluorescent light unit, and is covered by a shield or plate. The ballast has a hot and neutral wire at one end to receive power, and two blue wires a red one at the other end to supply power to the lights.
What is the difference between a ballast and a driver?
Fluorescent ballasts provide an initial spike of high voltage, generating an arc that travels from cathode to anode within the discharge tube. LED drivers convert high voltage, ac current into the low voltage, direct current that LEDs are designed to run on.
