Table of Contents
How does a log splitter work?
How does a log splitter work? The log splitter has a plunger that forces the wood into a moving or stationary splitting wedge. The plunger then continues to move the wood piece through the wedge, or the wedge through the wood, to separate the piece into two parts.
How do the hydraulics work on a log splitter?
Most log splitters use a hydraulic cylinder (like these) to push a cut piece of log into a sharpened wedge, which splits it. The cylinder is driven by hydraulic oil, under pressure, produced by a hydraulic pump. The oil from the pump runs to a hydraulic valve, which provides control over the movement of the cylinder.
How does a mechanical wood splitter work?
How Log Splitters Work An engine, normally a small four-stroke gasoline engine, provides the power for the system. The hydraulic oil pump creates a stream of high-pressure oil, which runs to a valve. The valve lets the operator actuate the hydraulic cylinder to split a log.
How many tons do I need for a log splitter?
Six-inch logs that are season require a 4-ton splitter, 12” seasoned logs need a 7-ton splitter, 12” green logs require a 16-ton splitter, 24” seasoned logs need a 20-ton splitter, and 24” green logs need a splitter that’s 30 tons or bigger.
How many horsepower is a log splitter?
A regular hydro splitter around 20-30 tons seem to have around 6.5hp gas engine. Get above ~30 tons and you typically get 9-11 hp range.
Does a log splitter need level ground?
Always position your log splitter on flat, solid, even ground. As with #5 above, since the recoil can cause the machine to shift, always position it on flat, solid, even ground for operation. Failure to do so may see it tip over and even fall on you.
Can you use a log splitter in the rain?
YES. Absolutely, you can leave the log splitter outside because it won’t cause any harm. If you’d like to cover it with a car cover or anything waterproof, that would be better. You just have to make sure that the cylinder was positioned upside down so that the rain won’t fill it.
What kind of gas goes in a log splitter?
Log Splitter engine exhaust contains carbon monoxide, a colorless, odorless, poison gas .
Is kinetic or hydraulic log splitter better?
One more benefit: gas-powered kinetic wood splitters are incredibly energy-efficient tools that use less fuel than their hydraulic counterparts. Obviously kinetic splitters have a lot to offer. However, in certain cases, a hydraulic splitter still might be the better option for some people.
How good are electric log splitters?
If you want to do you back a favor and replace your axe with a log splitter, there are many great options to choose from. While gas-powered versions are bigger and more powerful, electric splitters are quiet, less polluting – and usually quite sufficient for most home users.
Can you use an electric log splitter vertically?
The biggest advantage of being able to use a log splitter in the vertical position is that you can split massive logs without lifting them onto the splitter. If the majority of what you split is too large to lift, a vertical horizontal log splitter is what you need.
Is a log splitter easy to use?
Automatic log splitters can be activated with the push of a button, and are powerful enough to cycle through a log in as little as 13 seconds. Manual log splitters are also easier on the joints than using an axe, and depending on the size of the log, are still extremely efficient.
Do split wedges work?
If you’re looking to split logs or big rounds of wood, splitting wedges are just as important as a good axe or maul. They make the splitting process easier and safer, and allow you to do more with what you have – namely, your own physical strength and your main splitting tool (an axe, maul, or even sledgehammer).
What size log can a 27 ton log splitter split?
This powerful machine handles logs up to 24 inches long, weighing up to 100 pounds. Twenty-seven tons of splitting capacity deliver the power you need.
What size log can a 7 ton log splitter split?
Champion’s 7-ton log splitter features an integrated log cradle and low profile for easy loading. The 79cc engine easily powers through logs up to 19 inches in length and 50 lb.
What size hydraulic pump do I need for a log splitter?
This 16 gallon per minute hydraulic pump is a must have for any log splitter application. Fits a wide range of applications, most commonly used on log splitters with a rated force less than 35 TON. This 2 stage gear pump allows for maximum speed without a loss of pressure.
What is the fastest hydraulic log splitter?
This Hyper Split Fast Cycle log splitter by Tool Tuff Direct is one of the fastest hydraulic log splitters on the market today thanks to their new cylinder technology. Powered by a Ducar 6.5HP horizontal shaft engine. This proven engine has been tested in cold weather and high elevations.
What does P and T stand for in hydraulics?
Directional control valves are one of the most basic components in any hydraulic circuit. The supply port, which is called the ‘P’ or pressure port, a tank or ‘T’ port which takes the spent fluid back to the hydraulic tank, and a working port, called the ‘A’ port, that delivers the fluid to the load.
How do you speed up a hydraulic log splitter?
Only way to speed up a splitter is to move more oil. Either get a bigger pump or speed up the existing pump.
How do you adjust a 2 stage log splitter pump?
How to Adjust a 2-Stage Pump Adjust the hydraulic gauge by locating the adjustment screw on the back of the gauge. Use a flathead screwdriver to turn the screw. Adjust the pressure switch, located behind the hydraulic gauge, by using a wrench to loosen the lock-nut on the switch, then turning the adjusting screw.
