Table of Contents
The concrete slab should be four inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of “compressive strength,” which boils down to the amount of water used in the mix.
How thick do you pour concrete for a garage?
A standard garage slab should be at least 4 inches deep, depending on the subgrade condition (100 mm). You can raise the thickness to 6-inches if the garage has heavy machinery in it or heavy shelving loads. The concrete slab should be at least four inches thick. When heavy machinery sits on it, it needs to be thicker.
Is 4 inches of concrete enough?
For a concrete patio, the ideal slab thickness is at least four inches. There are times where thicker slabs will make more sense, but, most of the time, 4 inches is the perfect thickness for a concrete slab. It is, however, wise to make the perimeter of the slab an inch or two thicker.
How thick should a residential garage floor be?
The standard concrete garage floor is six inches thick and, with use of proper control joints, should be thick enough to withstand normal use.
What kind of concrete do you use for a garage floor?
The IRC requires that slabs be built with concrete with compressive strengths from 2500 to 3500 psi, depending on the climate. ACI goes further and recommends 4500-psi concrete for garages in the northern half of the country.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
How many yards of concrete do I need for a 24×24 slab?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
Do you need rebar for 4 inch slab?
The thickness of rebar should be no more than 1/8 that of the slab, so a 4” slab shouldn’t have steel greater than #4 or 1/2″ bar. It’s best to check with a Structural Engineer if your slab will bridge or cantilever. What is this? For 4” concrete slabs used for driveways and patios, #3 rebar is common.
How much weight can a 4 inch concrete slab support?
Typically we like to limit the weight to about 40 lb/sqft on an unknown 4″ slab. In most cases you can go to 80 lb/sqft in isolated spots, but unless you know roughly what the soil bearing and reinforcing is for that slab you might be looking at cracking.
Do you need wire mesh for 4 inch slab?
No, they do not. Larger projects or slabs may need steel reinforcement to provide support or extra strength. Wired mesh can also help resist cracking.
How thick should a concrete slab be for a shop?
Standard thickness of the shop floor slab used is 4 inches. Depending upon the type load coming upon the slab, the thickness is increased. Light Loads – For light cars or trucks, the concrete should be at least four inches thick.
Do you need footings for a garage?
Basic garage structures are not required to have foundation footings unless your lot slopes or has poor soil conditions. Most garages have a 4″ inch poured concrete slab-on-grade, and the structure is built directly on the slab. Garages built on a slope will often need a raised reinforced concrete slab with footings.
How thick should concrete floor be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks.
Does garage floor need rebar?
A garage slab or the garage concrete floor does not need rebars, provided it is 4” or less in thickness. Other forms of concrete reinforcement will however reduce cracks. Rebar is certainly required if the garage slab is 6” or thicker.
What is the minimum concrete strength for a garage floor?
The Alberta Building Code (ABC), and the Canadian Standards Association (CSA) requires a C-2 exposure (plain concrete exposed to freeze thaw conditions and subjected to deicing chemicals) at a minimum compressive strength of 32 MPa, or 30 MPa where local aggregates do not achieve 32MPa, with a 0.45 water/cementing.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How many yards of concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How many bags of concrete do I need for a 10×8 slab?
Regarding this, “how many bags of concrete do I need for a 10×8 slab?”, at 4 inches thick, generally you will need approximately either 58 bags of 60lb or 45 bags of 80lb of premixed concrete for a 10×8 slab, at 5 inches thick slab, either 73 bags of 60lb or 56 bags of 80lb premixed concrete are required, while at 6.
How many bags of concrete do I need for a 10×10 slab 4 inches thick?
The thickness of your 10′ x 10′ slab will determine just how many bags you need. The average thickness of a 10′ x 10′ concrete slab for a shed is 4 inches thick. At 4″ thick, your 10 x 10 slab will take 56 bags of concrete that weigh 80 lbs.
How much does a yard of concrete cover at 4 inches?
One Cubic Yard of Concrete: 4-inches thick – covers 81 square feet.
How many yards of concrete can a truck hold?
Each cubic yard costs about $65. However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load.
