Table of Contents
Galvanized, ceramic coated, or stainless steel screws are the best corrosion-resistant fasteners for pressure-treated cedar or redwood.
Can you use galvanized screws in pressure treated wood?
Fasteners for preservative-treated wood shall be of hot dipped zinc-coated galvanized steel, stainless steel, silicon bronze or copper. In the absence of manufacturer’s recommendations, a minimum of ASTM A653 type G185 zinc-coated galvanized steel, or equivalent, shall be used.
Can you use steel screws in pressure treated wood?
Pressure treated wood is most commonly used for construction in areas exposed to harsh outside conditions. There are only two recommended corrosion resistant systems which should be used with pressure treated wood: hot-dip galvanized steel and stainless steel fasteners and industrial consumables.
What hardware should I use for pressure treated wood?
Hot-dip galvanized or stainless steel fasteners, anchors and hardware are recommended by the Preservative Treated Wood Industry for use with treated wood. This has been the position of this industry for years and their position has not changed with the transition to the alternative copper-based products.
Can deck screws be used with pressure treated wood?
Galvanized screws work well with pressure-treated decking, while Redwood or Western Red Cedar decks are usually built with stainless steel screws to prevent staining around the screw heads.
Are GRK screws good for pressure treated wood?
GRK fasteners are ICC code approved for exterior use in ACQ pressure treated lumber and have the strength to meet all your general construction needs. A building inspector will be able to use an ESR report to code approve your construction projects.
Are galvanized nails OK for treated wood?
For most applications, however, best nails for pressure treated lumber are either hot dipped galvanized nails and bolts. For screws we recommend using ones that have a protective coating that is designed for use with pressure treated lumber. one example would be Outlaw fasteners.
Are stainless steel screws good for treated lumber?
Corrosion-resistant stainless steel screws, nails and bolts in grades 304 and 305 can be used for copper-treated wood in most areas, while grade 316 should be used in coastal areas. But stainless steel fasteners can cost five to 10 times more than similar galvanized fasteners.
What screws to use for outdoor wood?
Deck screws are basically production screws that have been plated and/or coated to increase their corrosion resistance. They’re great for outdoor projects, like playhouses or decks. For even greater resistance to rust and corrosion, the two best screw materials are silicon bronze and stainless steel.
What kind of screws should I use for decking?
A good all-around choice is #10 decking screws—generally in 2 1/2- to 3 1/2-inch lengths. Decking screws are sharp, tapered, self-sinking, and coated for corrosion resistance. With a cordless drill/driver, you can drive them about as fast as nails.
What happens to screws in treated lumber?
However, ACQ treated lumber is more corrosive to metal, so the right fastener is key to a safe, long lasting deck, fence or other outdoor project. This reaction accelerates the corrosion rate of the fastener. Additionally, the organic components of ACQ attract water, further increasing corrosion on the fastener.
Can you drill into pressure treated wood?
When building a deck, you often have to drill holes in pressure-treated wood for bolts or wires. The best practice is to apply a wood preservative to the inside of the holes to prevent rot, the same way you apply preservative to end grain after making a cut.
How long should deck screws be?
Length. The standard length for deck screws ranges from 1 ½ inches to 6 inches, depending on the size of the deck boards, joists, railings, and posts.
Does pressure treated wood corrode metal?
Pressure treated wood is a popular product for outdoor construction, i.e. bridges and decks. When wood treated with the new chemicals was exposed to metal parts, the metal tended to corrode, even moreso in water contact environments, in only a few years.
What fasteners should be used in CCA treated timber?
Bright steel nails have successfully been used for decades in this environment. CCA H3. 2 timber is similar in that bright steel nails will not corrode provided a low moisture content is maintained.
Can you use joist hangers with treated lumber?
The chemicals used in pressure-treating lumber, including fire-retardant chemicals, are corrosive to bare steel. Stainless steel joist hangers are available for contact with more corrosive treated lumber.
Can composite deck screws be used on wood?
These screws are specially designed to eliminate the mushrooming and blemishes that can occur on composite materials. They are also an excellent choice for wood decks, where the top threads work to pull down and hold warped lumber and lock the boards together.
Are deck plus screws good?
They worked great. With the T25 Star bit connection, every screw went in true and smoothly without slippage. It was great to have the T25 bit included in the box. I used the same T25 bit to drive in over 1000 screws and it’s still in good shape.
Can you frame with GRK screws?
For use in framing, floor work, decking top boards, railings, and other remodeling applications. For use in interior and exterior conditions, and the GRK Climatek coating is approved for use in treated lumber.
Do I need to pre drill with GRK fasteners?
No pre-drilling required for most GRK products, unless required or specified by building material. Always place deck boards with outer edge of growth rings facing up (bark side up).
Will GRK r4 screws rust?
GRK’s Climatek™ coating meets or exceeds standards, including AC257, approved for use in various types of preservative treated wood. Designed for interior/exterior use, the golden finish nicely matches most wood finishes. GRK’s Stainless Steel Screws are made from 305 grade wire which will not rust.
