Table of Contents
When lighting the pilot, make sure the knob on the gas control valve is fully pushed in. Keep the knob pushed in while repeatedly clicking the spark igniter button. Hold the knob in and click the igniter button repeatedly for 90 seconds. Newly installed water heaters have air in the gas line.
How do I reset my Whirlpool water heater?
Press the small reset button in the center of the thermal switch. If it’s tripped, you may be able to hear it click. Even if you do not hear the thermal switch click, try lighting the pilot using the instructions on the water heater’s label. If the Status Light now begins to flash, the thermal switch probably tripped.
How do you light a self lighting water heater?
Lighting the Pilot Light on an Automatic Hot Water Heater All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!Feb 13, 2020.
How do you light an electric water heater?
Lighting A Hot Water Heater Pilot Light Set the temperature control. to its lowest setting. Set the on-off control. to the pilot setting. Press the hot water heater. pilot button down and. hold it. While looking through the the sight glass slowly press the spark generator until you here it click. You should see a spark.
How do you reset the pilot light on a water heater?
Turn the knob to “Off,” and then wait five minutes for the gas to clear before you follow these steps: Open the door/cover over the pilot light access. Use a flashlight or a headlamp to find the burner inside. Turn the gas knob to “Pilot,” press and hold it down. While still holding the gas down, light that pilot.
Why is my Whirlpool hot water heater not working?
Make sure both thermostats are pressed firmly against the tank. Check the power at the upper thermostat connection terminals that transfer power to the lower thermostat. If no power shows, the lower thermostat has failed. If there is power but no heat at either element, then that element is bad.
How do you light a Dux water heater?
How to relight a pilot light Turn the control knob fully clockwise to the “•” (off) position. Wait five (5) minutes so any build- up of unburnt gas can escape. Turn the control knob to the (pilot) position.
How do you light a gas water heater with an electric igniter?
Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.
How do you light a pilot light?
If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.
Is there a pilot light on electric water heater?
There’s no gas or pilot light involved in electric water heaters. If the power to your electric water heater is off, you may have an electrical issue requiring professional assistance. You will need to reignite a gas water heater that does not light automatically.
How do I know if my electric water heater is on?
Start by looking for an access panel on the side of the water heater. If you remove it and see a blue flame, that’s a pilot light, which only gas models have. Connected pipes are also indicators of gas, while an electric water heater will simply have a cord going into the top or side of the unit.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
Why is my hot water heater not lighting?
If you have a natural or propane gas water heater, chances are the pilot has gone out. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
How do I know if my pilot light is lit on my water heater?
It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.
What causes a pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
What trips the reset button on a hot water heater?
If a water heater reset button keeps tripping, the first area to inspect is the thermostat. With an electric water heater, you have two thermostats; one upper thermostat and one lower one. When this happens, the thermostat may never turn off the heating element, which causes the reset button to trip.
