Table of Contents
The ubiquitous lumber product known as the 2×4 does not, in fact, measure two inches thick by four inches wide. The naming of this building material is the result of compromise between forestry technology, species’ properties, forest composition, transportation efficiency, construction speed, and price competition.
Why isn’t a 2×4 actually 2×4?
DIMENSIONAL LUMBER: In the past, when a timber was called a 2×4 [or “two-by-four”], it actually measured 2 inches by 4 inches. Because of this extra milling, a 2×4 no longer measures a full 2 inches by four inches. Instead, a 2×4 is really only 1 1/2″ by 3 1/2″.
Why do they call them 2 by 4?
Without the rough edges, what went in as a 2-by-4 planks of rough-sawn wood is now a tongue-tripping 1.5-by-3.5, having lost approximately ¼-inch on all sides to the planer and drying processes. “Once upon a time, 2-by-4s really were 2 inches by 4 inches,” Stephens says.
Why is lumber not the actual size?
The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.
Why is lumber a half inch short?
The simple reason why 2×4 is not 2 inches by 4 inches is that lumber mills trim off rough or warped surfaces of a 2×4 to give it a more polished and finished look. By planning the lumber on all four sides, the original 2×4 is now reduced to 1 ½ inches by 3 1/2 inches.
What do they call a 2×4 in Europe?
I cant speak for the hole of europe, but at least in Norway a “2×4″ is 48×98 mm. If you go to a lumberyard, you buy 48×98 as everything is measured in metric, but in the daily speach most people still use the term 2×4, 2×8 aso. The Inch measurement is in use as long as we speak about size on TV(40″) and cartyres (15”).
Why is lumber smaller than the size it says?
Typically, that rough cut is smaller than the nominal dimensions because modern technology makes it possible to use the logs more efficiently. For example, a “2×4” board historically started out as a green, rough board actually 2 by 4 inches (51 mm × 102 mm).
Are 2×6 really 2×6?
In North America, the 2×6 size is actually referring to the lumber’s “nominal” dimension. A 2×6’s real or true dimension is 1.5″ x 5.5″ – within the industry it is referred to as its “actual” size. The nominal size is used when discussing lumber nearly 100% of the time! Same for 1×4, 2×4 and 4×4 etc.
What is a 2×4 in Australia?
This is similar to this question about metric measurements. In Australia, a common measurement is 90mm x 45mm for timber. A 4×2 would be (approx) 100mm x 50mm but, as I understand it, that is the milled rather than final measurement.
Is lumber a timber?
In the US and Canada, timber is typically used to collectively refer to trees—or the wood of such trees—that have yet to be cut or processed, while lumber typically refers to wood that has been processed as a building material (boards and planks).
When did they stop using true 2×4?
This pressured further compromise because thinner 2x4s were a way to compete in price with wood alternatives. Size standards, maximum moisture content, and nomenclature were agreed upon only as recently as 1964. The nominal 2×4 thus became the actual 1½ x 3½, imperceptibly, a fraction of an inch at a time.
What is the longest 2×8 you can buy?
In general, a 2×8 will span 1.5 x 8, so 12-feet. Based on all factors though, a 2×8 joist span is 7′-1” to 16′-6”, and a rafter 6′-7” and 23′-9”.
Why is a 4×4 actually 3.5×3 5?
no, it is just a bit over 3.5″x3. 5″ for clearance. 2×4 and 4×4 boards are no longer the actual number, but as you state–they are 1/2″ LESS. the base fits nicely to a standard 4×4.
What is the actual measurement of a 2×10?
Nominal vs. Actual Measurements of Dimension Lumber Nominal Size Actual Size 2 x 8 1 1/2 x 7 1/4 inches (38 x 184 mm) 2 x 10 1 1/2 x 9 1/4 inches (38 x 235 mm) 2 x 12 1 1/2 x 11 1/4 inches (38 x 286 mm) 4 x 4 3 1/2 x 3 1/2 inches (89 x 89 mm).
How wide is a 1×10?
1x Board Sizes The larger 1x boards (1×8, 1×10, etc.) lose 3/4 inch in width. That means a 1×10 is actually 3/4 inch in thickness by 9 1/4 inches.
What are the actual dimensions of a 4×4?
Actual Size The outside dimensions of the standard 4×4 measure 3-1/2″ x 3-1/2″, and the outside dimensions of the standard 6×6 measure 5-1/2″ x 5-1/2″. Likewise, how wide is a 2 by 4? A piece of surfaced (sanded smooth) 2×4 lumber actually measures 1½ inches thick and 3½ inches wide.
What do they call a 2×4 in Canada?
In Canada, where we adopted the metric system in the early 80s, we call them 2x4s.
When did lumber dimensions change from actual to nominal?
Early concepts called for rough lumber to be of full nominal size, often in the dry condition. After World War I, the increasing demand for construction lumber led to the first national size standard in 1924. This was revised in 1926, 1928, 1939, and 1953, while still another revision is proposed for adoption in 1964.
What is a 2×4 in UK?
2″x4″ timber is nominally 47mm x 100mm but is “regularised” with 3mm off the thickness and 5mm off the width, so it ends up being around 44mm x 95mm (may be nearer 45mm on the width).
