Table of Contents
How do I know if my gas fireplace is off?
Why won’t my gas fireplace shut-off?
Usually there is a rocker switch that is located around your burner which, if in the “ON” position, it will override the remote. Turn the switch to “OFF.” There may be a wall switch that allows you to turn your burner on. Slide the switch on the receiver back to the center or remote position.
Where is the shut-off valve for a gas fireplace?
A) located just before the gas meter. This valve, often called the street-side valve, is normally a rectangular nub (Photo 1). When the long side of the nub or handle is parallel to the incoming gas line, it’s open and the gas is flowing. When it’s turned a quarter turn, perpendicular to the incoming pipe, it’s closed.
How do I turn off my gas fireplace key?
Turning It Off For fireplaces with a control panel, it’s as easy as turning the control knob to off. You should close or turn off the emergency gas valve. For those with a key valve, just insert the fireplace key into the slot and turn it until the valve closes. This cuts off the gas supply, and the pilot will go out.
Do gas fireplaces turn off automatically?
Nearly every new gas fireplace comes equipped with safety features such as a 100% fail-safe shut-off valve. If the pilot flame goes out, the gas flow will automatically turn off. This device automatically shuts the gas off if the temperature in the fireplace gets too cold or if too much carbon monoxide builds up.
What does the on and off switch do on a gas fireplace?
The wall switch sends an electrical signal to your fireplace to open a valve and release the gas for the pilot light to light it. Without power most fireplace valves will not open. I have a new home with gas fireplaces. I do not know how to use them yet, but I smell gas near one of them.
How long does it take for a gas fireplace to turn off?
It takes a fireplace blower about 10-20 minutes to complete the process of it turning on and off.
How do you turn off a superior gas fireplace?
To make the flame in the fireplace higher or lower, simply adjust it by turning the gas valve counterclockwise to increase it or clockwise to decrease it as desired. To shut down the fireplace completely, turn the gas valve clockwise all the way to the “off” position.
How do I turn off my heat and Glo gas fireplace?
Remember to shut the gas supply valve off (picture #1). If it remains lit, press the valve knob in slightly and rotate counter-clockwise until the word “ON” is in the 6 o’clock position. Finally, turn the unit’s ON/OFF switch (or wall switch or remote control) to the “ON” position to start your fire.
How do I shut off my gas supply?
Go to your meter. Locate the gas safety shut-off valve at your gas meter and turn it to the ‘off’ position. It is off when the lever is at a right angle to the pipe.
How do I shut off my gas line?
Locate your main gas service shutoff valve. It’s usually the first fitting on the natural gas supply pipe coming out of the ground next to the meter. With a wrench, turn the lever in either direction until it is crosswise to the pipe. Once the gas is turned off, leave it off.
Can you leave the pilot light on a gas fireplace?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
Should I turn off the pilot light on my gas fireplace in the summer?
Your Utility Bill Perhaps the most important reason to turn off gas fireplace pilot light in summer is because of the money and energy you will be saving. If you leave the pilot light on during the summer it is simply sitting there burning gas, which is wasting gas and contributing to an exorbitant energy bill.
Is it safe to leave a gas fireplace on all night?
The short answer is this: gas fireplaces that are fully vented and have safely and properly sealed glass fronts are fine to be left alone to run continuously.
Does damper need to be open for gas fireplace?
One caution, though: Fireplaces with installed gas logs are required to have the damper open at all times. That’s either because a pilot light is constantly burning under the logs or because the homeowner might forget to open the damper when he or she turns on the fire. Those gases contain carbon monoxide.
What is the switch on my gas fireplace?
Gas Fireplace Wall Switch: What, Why & How Simply put, a fireplace wall switch is a toggle switch that opens or closes the circuit between the thermopile and the gas valve. It operates at millivolts, meaning it is able to operate at very low-voltage electricity(350-1000 millivolts).
What are the 2 switches for on my gas fireplace?
Question: There are two wall switches on the wall beside the gas fireplace. The top switch ignites the flame.
Do gas fireplaces need electricity to turn on?
In addition, all direct vent gas fireplaces are sealed, keeping emissions out, and are vented to the exterior of your home using the natural buoyancy of warm air (warm air rises), meaning no electricity is needed to operate your gas fireplace or gas fireplace insert safely.
