Table of Contents
Go behind the engine and unscrew the idle air control valve from the throttle body. Pull the electrical plug off the control valve. If the top has a release tab, then squeeze that as you pull. Take out the idle control valve and flip it over.
How do you test a Ford IAC valve?
Checking the IAC valve internal circuitry: Set the ignition key to the “off” position. Unplug the IAC motor electrical connector. Turn the ignition key to the “on” position; don’t start the engine. Set your multimeter to 20 volts on the DC volts scale. Connect your meter’s black lead to the battery negative post.
How do I know if my idle air control valve is bad?
Common signs include irregular or unusually high idle speed, the Check Engine Light coming on, and stalling while idling.Usually a bad or failing idle control valve will produce a few symptoms that can alert the driver of a potential issue. Irregular idle speed. Check Engine Light comes on. Engine stalling.
What happens if I unplug the idle air control valve?
If it works properly, stopping it would cause panic to your inactive engine. Normally, if you turn on your car, the inactive air control valve will increase and decrease the rpms engine slowly.
How many ohms should a IAC valve have?
Using an ohmmeter, measure the resistance between pins 3 and 2 on the (IAC) valve. Resistance should be 10-14 ohms. If resistance is ok, proceed to the next step.
How do I fix code P0505?
What repairs can fix the P0505 code? Replacing the IAC valve and cleaning the throttle body and passages. Removing carbon from throttle body and IAC passages and clean IAC. Repairing a vacuum leak in the engine intake manifold vacuum system or gaskets.
How do you reset your idle air control valve?
Turn the ignition ON and leave on for several seconds then turn the ignition OFF to allow the ECM to reset the IAC valve. You should be good to go.
How do you test a 4 pin IAC valve with a multimeter?
5 Steps on how to test iac valve with multimeter Step 1: Locate the iac valve from service manual. Step 2: Inspect the IAC Valve operation. Step 3: Test the resistance of the coils. Step 4: Check supply voltage from the ECU. Step 5: Check the coil for short circuit and for short circuit to earth.
How do I clean my idle air control valve without removing it?
How To Clean Idle Air Control Valve Without Removing It Prepare the working area. Locate the idle air control valve. Remove the filter box and the air duct. Disconnect the clamps that connect the air duct to the throttle body. Locate the passage to the idle air control valve. Spray the hole with throttle body cleaner.
What is an IAC valve Ford f150?
The idle air control (IAC) valve is an electronically controlled valve that allows air to bypass the throttle body.
Can a car run without an idle air control valve?
The engine would be unable to start or run unless the throttle was slightly open, because the IAC’s (Idle Air Control) job is to let a controlled amount of air into the cylinder when the throttle is closed. If the IAC is stuck closed, the only way for air to get in is past the throttle plate.
What causes intermittent rough idle?
The most common cause of rough idle is a vacuum leak or a failed PCV valve. It could also be caused by other air-fuel mixture-related issues like bad fuel injectors, EGR valves, or low compression. In rare cases, it is caused by misfires from a bad spark plug or coil.
Can you drive with a code p0507?
This trouble code will not prevent your vehicle from driving, but you may experience engine stalling, high idle rpm, harsh engagement of transmission, difficulty starting, and/or surging idle.
Can you test idle air control valve?
Test and Clean Procedure Pull the electrical plug off the control valve. If the top has a release tab, then squeeze that as you pull. Take out the idle control valve and flip it over. You should see the valve openings there.
Can you clean idle air control valve?
How do you clean an IAC valve? After relocating the IAC valve, you need to unscrew it and detach all the wires. You can clean it by soaking it in gasoline and blowing compressed air into it. Then, reattach it with the screws and reconnect the wires.
Can idle control valve cause misfire?
IDLE CONTROL VALVE CONTROLS THE ENGINE IDLES, IT CONTROLS THE SPEED OF THE ENGINE UP AND DOWN. IF YOU HAD A MISFIRE I WOULD START LOOKING AT THE AIR INTAKE FOR LEAKS CHECK ALL THE PLUGS MAKE SURE THEY SPARKS ALL GOOD. IT CANT CAUSE A MISFIRE UNLESS YOU HAVE A LEAK AROUND THE INTAKE MANIFOLD TO IDLE VALVE SEAL.
Will bad IAC cause hard start?
If your vehicle has the 4-liter V-6, the problem may be a faulty idle air control valve. Whenever you start the engine, the throttle is closed so the valve meters the proper amount of air for combustion. If it allows too much or too little, the result is hard starting and often rough idle.
How do I fix code P0507?
What repairs can fix the P0507 code? Replacing or cleaning the idle air valve. Repairing the intake air leak. Repairing the charging system. Cleaning the throttle body. Replacing the power steering pressure switch.
Can I drive with a P0505 code?
Trouble code P0505 should be diagnosed and repaired as soon as possible. Not recommended, however, you may drive your vehicle while trouble code P0505 is present unless the engine stall or stumbling is is severe enough to hinder proper vehicle operation. Erratic or lack of idle control may be noticed.
How do you fix the idle air control system RPM higher than expected?
Check the PCV valve as well and see if it is blocked and needs a new replacement. Inspect the IAC (Idle Air Controller) if it is equipped, and verify its performance. Try swapping in a new throttle body (if available) and see if it can fix the problem.
