Table of Contents
If you’re using typical architectural shingles and 3/8-inch-thick sheathing, you’ll need 1‐inch nails. If your building codes require thicker sheathing, you’ll need 1 ¼-inch nails. When installing thicker shingles, you may need to use a longer nail in order to penetrate the OSB beneath fully.
How long should roofing nails be?
The length of each nail must be a minimum of 1¼ inches long, and for roof-overs, Atlas recommends a nail length of at least 2 inches. Nails of the proper length should penetrate three-fourths of an inch into the roof deck.
What size roofing nails are best?
Roofing nails should be 1-1/4 to 2 inches long to ensure that it sufficiently penetrates and embeds in the roof sheathing. To calculate the appropriate roofing nail length, add the thickness of the shingles and underlayment to the thickness of the sheathing. Nail shank diameter should be at least 11-12 gauge for roofs.
What type of nail is used for asphalt shingles?
Galvanized roofing nails tend to resist rust formation, and they are a suitable option for asphalt shingles. Owens Corning requires using either galvanized steel, stainless steel, or aluminum nails to affix shingles.
How long should nails be for 2 layers of shingles?
Layers. If you are putting a layer of asphalt shingles over an existing layer of asphalt shingles on to a 3/4-inch deck or a plank deck then you should be using 1 1/2-inch nails. If your decking is less than 3/4 inch then a 1 1/2-inch nail will suffice.
Can roofing nails be too long?
Yes, they can. If they are too long, they will protrude through the sheathing at the roof overhang and be visible.
How long should ridge cap nails be?
You need to use at least 2-inch-long nails for roof cap shingles installation. Why? The standard 1 and 1/4-inch nails are not long enough to penetrate through all the roofing material up near the ridge.
How many nails do I need for roofing?
Roofing Nails Generally, you should use four nails per shingle in the field of the roof, and 5 nails per starter shingle. For regular three-tab shingles, this would require 320 nails per square for field shingles.
What is high nailing of a shingle?
A high nail is a nail installed above the nail line on the shingle. High nails cannot be seen as they are covered by the next course of shingles but they can cause big problems. When the shingle is nailed too high the nail does not penetrate the shingle below it.
Is it better to hand nail shingles?
While air gun nailing might seem faster, a well-trained hand nailer can do it almost as fast. The key difference between the two is accuracy. Hand driving nails into shingles allows for the roofer to place the nail on the proper nail line and then drive the nail in.
What nails do you use for roofing felt?
Galvanised nails can be used in a wide range of applications, but are most commonly used in the installation of asphalt shingles and felt on outbuildings, sheds and more – wherever adverse weather conditions are common, galvanised nails are a good choice.
Is it OK to put 2 layers of shingles?
Two layers of shingles trap more heat, which in turn damages the shingles and shortens the life span of the roof. Adding a second layer could compromise the structure of your roof. Problems fixing leaks: A second layer of shingles only complicates the job when a roofer is trying to fix a leak.
Should roofing nails be visible?
Yes, and there are two types of nails that are normal to see in an attic: 1) The ring-shank nails used to secure asphalt shingles to the plywood or OSB roof sheathing typically penetrate into the attic 1/4” or more.
Are roofing nails supposed to use plywood?
The code states that the nails only penetrate when the roof deck thickness is below 3/4 of an inch. To hold snow, ice, and withstand wind, it has to be at least one inch thick plywood.
Can you nail over shingles?
When you nail-over your old shingles, most of the typical roof replacement process is left out. Nailing-over doesn’t require a tear-off, dump fees, underlayment installation, new flashing, or new decking.
Can I Staple shingles?
Fasteners for asphalt shingles should be roofing nails or staples. Both nails and staples have sufficient strength to resist small uplift load on the shingles, as long as the tabs remain sealed. If staples are properly installed, they offer nearly the same wind resistance as nails.
Can you use 3 tab shingles for ridge cap?
The ridge cap, the course of shingles on the very ridge of the roof, can be made from available 3-tab shingles. Two simple cuts create three pieces that can be used to finish the shingle project.
Are ridge cap shingles different?
Ridge cap shingles are like regular shingles in that they use the same material and offer the same look in terms of color; but they are different in that they are specially designed to cover the ridges of the roof, which are high-stress areas that need more protection, unlike with metal roofing.
