Table of Contents
How do you relight a pilot light on a water heater?
All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!Feb 13, 2020.
Is it safe to relight your water heater?
Most homeowners can relight a pilot light themselves without any issue, but it’s important to be safe when dealing with a gas-powered hot water heater. You should always proceed with care when relighting a pilot light, since the gas used to power your hot water heater is flammable and potentially dangerous.
What do you do when your hot water heater pilot light goes out?
What should you do when your water heater’s pilot light goes out? Turn the thermostat to the lowest setting. Turn the on/off/pilot switch to the “pilot” position. Remove the outer and inner panels to access your pilot light.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How long do you have to wait for hot water to come back?
Ideally speaking, an electric water heater takes around 60 to 80 minutes to release hot water with a tank capacity of 40-gallon. If the tank capacity is 80-gallon, the recovery time can be more than two hours.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do I know if my pilot light is out?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
Where is the pilot light on a hot water tank?
The pilot light on most water heaters is located at the base of the unit, below the gas control valve. Open the access panel or door to the burner chamber and look inside. There, you’ll find the pilot light tube, which should have a steady blue flame. If you don’t see the flame, the pilot light is out.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
How do I turn my gas back on after disconnecting?
You are going to need a wrench or gas shut off tool to do this. Very slowly, turn the meter back into the on position. The lever should be in line with the pipe after making a ninety-degree turn. Finally, you can re-light any of the pilot lights in your appliances.
How much does it cost to have a pilot light lit?
Running a pilot light for 1 hour costs about 1 cent (0.62 cent/hour for natural gas and 1.64 cent/hour for propane). Monthly costs of running a pilot light range from $4.49/month (natural gas) to $11.34/month (propane).
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How do I get my hot water running again?
If your home has no hot water, turn off the heater first. Then, reset the circuit breaker. If the breaker tripped, your home will receive hot water again after about an hour. A circuit breaker that continues to trip is a bad sign, so hit the reset button.
How can I make my hot water come back faster?
How to Get Hot Water Faster Insulate the Pipes. If you think your water pipes are to blame for your hot water troubles, adding insulation might improve your situation. Hot Water Recirculation Pump. Replace Fixtures with a Higher Flow Rate. Upgrade to a Tankless Hot Water Heater. Routine Preventative Maintenance.
Why would pilot light go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
How do you light the pilot on a gas water heater?
Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. While still holding the gas down, light that pilot.
How long does it take for the water to get hot after lighting the pilot?
Once you’ve got your water heater back up and running, it’s going to take awhile before you have hot water. How long depends on how large of a tank you have. In general, you should expect to wait between 30 to 40 minutes before your tank is fully heated.
