Table of Contents
How much quikrete do I need for a fence post?
1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.
How much concrete do you need for a fence post?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.
How many 50lb bags of concrete do I need for a fence post?
For reference, a 40-pound bag of concrete typically yields about 0.3 cubic feet, a 50-pound bag yields 0.37 cubic feet, a 60-pound bag yields 0.45 cubic feet, and an 80-pound bag yields 0.6 feet. This means that in the example above, each post would require about eight 50-pound bags.
How much quikrete does it take to fill a post hole?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.
How much area does a 50 lb bag of quikrete cover?
Regarding this, how much does a 50 lb bag concrete cover?, as 133 lb concrete = 1 CF, so a bag of 50 lb concrete = 50/133 = 0.375 CF, therefore, a 50 lb bag of concrete approximately cover around 1.5 square feet area upto standard depth of depth of 3 inch for your patio and sidewalk.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
How big of a hole do I need for a 4×4 post?
The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.
How much post mix do I need per post?
How much Post Mix do I need for a fence post? The exact amount of Post Mix Concrete needed will vary depending on the width and depth of the hole, but as a general rule you’ll need about one and a third bags for a standard fence post.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
How many bags of cement do I need for 12×12?
of 40lb bag = 1.76 ÷ 0.011 = 160 bags. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yields, at 5 inch thick, for a 12×12 slab you will need 2.22 yards of concrete, so number of 80lb bag of concrete = 2.22 ÷ 0.022 = 100 bags, No.
How many bags of concrete do I need for a 4×4 slab?
As per calculation, for a 4×4 slab at 4 inch thick, generally you will need approximately either 12 bags of 60lb or 9 bags of 80lb of premixed concrete, at 5 inches thick slab, either 15 bags of 60lb or 11 bags of 80lb premixed concrete are required, while at 6 inches thick slab, either 18 bags of 60lb or 14 bags of.
What is the best concrete mix for fence posts?
For a small to mid sized job I recommend going with premixed. The best concrete mix for fence posts I’ve found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It’s 4000 psi, easy to work with, sets up fast, and doesn’t need to be mixed. Just pour it in the hole and soak with water.
What happens if you add too much water to quikrete?
When a concrete mixture is too wet, it causes a greater amount of shrinkage during the drying process than is needed. As a result, the concrete has a great likelihood of cracking and for those cracks are likely to be a fairly good size. A watery mix actively reduces the compressive strength of the dried concrete.
How do you calculate concrete post holes?
Calculate Concrete Volume With the volume of the submerged post and the volume of the hole figured out, subtract the post volume from the hole volume, and you will have the volume of concrete needed for each hole. Simply multiply that amount times the number of posts to get a total quantity.
How many bags of quikrete do I need for a 10×10 slab?
The thickness of your 10′ x 10′ slab will determine just how many bags you need. The average thickness of a 10′ x 10′ concrete slab for a shed is 4 inches thick. At 4″ thick, your 10 x 10 slab will take 56 bags of concrete that weigh 80 lbs.
How many cubic feet are in a 50 lb bag of quikrete?
One 50-pound bag of Quikrete Fast Setting Concrete Mix yields about . 375 cubic feet.
How many 60 pound bags of quikrete are in a yard?
If you’re using 60lb bags of concrete, you’ll need 60 bags to make a yard. If you’re using 80lb bags of concrete, you’ll need 45 bags to make a yard.
How far apart should fence post be?
Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.
How tall should a fence be for a 6 foot fence?
As a general rule of thumb, you’ll need to place at least 1/3 the height of the post in the ground. For example, a 6-foot tall fence will need at least 2 feet of post in the ground.
Can you put dry concrete in a post hole?
Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
