Table of Contents
If the hot tub is not heating, the light is blinking because the water temperature has dropped more than 2 degrees from the set temperature. If the hot tub is not equipped with either salt water system, power the tub off at the breaker or unplug.
Why is my Hot Springs hot tub flashing?
When the power indicator is FLASHING RED, this means that the heater high limit has tripped. This means that the tub could be above its temperature limit or that the filters are clogged. The red flashing lights usually means that you’ll need to call for service.
How do I reset my hot tub heater?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. Press the high-limit reset button. Turn on your spa and observe its operation. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
Why is my hot tub lights not working?
Blown fuse Another common problem that can occur with your hot tub lighting is that the fuse has blown. This is normally a tube type fuse. Check to see if the glass on the tube has discolored or one of the wires connected to it is broken. If these signs exist, you may need to replace it.
How do I know if my hot tub heater is working?
To test if a bad heater is causing your tripped breaker, you can disconnect the copper tabs (or wires) from the spa pack to the heater element. Once disconnected, turn the power back on. If the breaker stays on, you’ve determined that the heater is bad.
How can you tell if a heating element is bad?
Touch a probe on the multitester to each screw on the element. If you get no reading, or a maximum reading, the element is bad. Elements do have some resistance, so a reading of 10-16 ohms is normal, with higher ohm readings for 3,500 watt elements and lower readings for 5,500 watt elements.
Why is my hot tub not keeping temperature?
pressure switch or thermostat. mode setting – could be set on Economy or Sleep which will not maintain the temperature – set on Standard. or even simply that there is not enough water in the Hot Tub or jets closed.
How do I know if my hot tub control panel is bad?
Spa Control Panel Displays Incorrectly Error messages or error codes may indicate the problem. Flickering display may indicate low voltage from transformer. Partial display may indicate dirty contacts or moisture. Blinking lights or flashing — indicates a system reset is needed.
Where is high limit reset on hot tub?
The hot tub high limit switch is sometimes triggered when you’re refilling your hot tub and can be reset by pressing the large red button on your spa pack.
Why does my hot tub say error?
A hot tub flow error indicates that there is a problem with the flowing of water through the hot tub heater. The most common causes for this are a dirty or damaged filter, low water levels, air in the pipework or a faulty pump or sensor..
What does run pumps purge air mean?
Run Pumps Purge Air Display Message Print The purpose of Priming Mode is to allow the user to run each pump and manually verify that the pumps are primed (air is purged) and water is flowing. This typically requires observing the output of each pump separately and is generally not possible in normal operation.
How long do hot tub lights Last?
Spa light bulbs don’t last forever, and this may be the first thing to check. Even LED spa light bulbs will fail, despite some claims that they last nearly forever, they usually burn out within ten years.
Will an airlock clear itself?
Airlocks do sometimes fix themselves, but it isn’t a risk worth taking. Airlocks occur when air becomes trapped in the hot water or central heating system. Vapour becomes caught in a high point of the pipework because the gas is less dense than the water in the system.
What causes hot tub air lock?
Hot tub air lock happens when air gets trapped inside the plumbing, and the circulation pump is unable to prime. This keeps water from flowing through the water lines, preventing the pump(s), heater and jets from working normally.
How long does it take for a hot tub to heat up?
If your hot tub is located inside, and the air temp is around 76 degrees, it will take about 4 hours to heat up your spa to 100 degrees. The lower the outside temps the longer you will have to wait before your spa is ready. Therefore, by leaving the cover on while it’s heating up you can help it warm up faster.
Why is my hot tub cold?
My Water Gets Hot, Cold, Hot Again Start by cleaning your filter, checking for circulation blockages, and topping off your water if necessary. Check whether your pump turns on. Your pump has to be running in order for the spa to heat up. If the pump isn’t working, you may need to replace it.
How long do hot water heaters last?
It would be nice to know when the time is right to replace your water before it springs a leak and causes an inconvenience or worse yet, damage to your home. Typically a residential hot water heater lasts between 6 and 13 years. Beyond 12 years, you are on borrowed time!Apr 19, 2012.
Do you have to drain water heater to replace element?
It is possible to change your water heater’s heating element without draining your tank. Although, keep in mind that it can be a bit more challenging.
How much is a water heater element?
A water heater element can cost between $10 and $60 and can be found at most home improvement stores. If you’re comfortable with light electrical work, replacing a water heating element is a DIY task.
