Table of Contents
What is the best way to apply Thompson’s water Seal to a fence?
Can you spray Thompson’s water Seal on a fence?
Treating the Fence For the convenience of a one-day project, Thompson’s® WaterSeal® Exterior Stains can be applied to damp, freshly cleaned wood. When treating your fence and applying a Thompson’s® WaterSeal® waterproofer or fence stain, follow the label’s application instructions carefully.
Can you use a sprayer to apply Thompson’s water Seal?
You should be able to work with any sprayer that gets the job done. This can be a deck stain pump sprayer or garden pump sprayer with a hose. However, Thompson’s water seal manufacturer recommends using a plastic sprayer with a brass wand attachment when applying their products.
When can you walk on Thompson water Seal?
How long before you can walk on Thompson Water Seal? Surfaces coated with Thompson’s water seal should be dry in about 24 hours. That is all the time you need to wait before you can walk on the sealed surface if you followed the application instructions correctly.
How Much Thompson water Seal do I need for my fence?
Divide the total square feet of fence to be stained by the coverage listed on the can. For example, if you have 1,000 square feet of fence and the stain says that 1 gallon covers 200 square feet, you would divide 1,000 by 200, which equals 5 gallons to cover the fence.
Does Thompson’s water seal work?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
Do you need to seal both sides of a fence?
A question that customers sometimes ask is whether both sides of the fence should be sealed. In reality, if one side of the fence faces a neighbor and they choose not to stain or seal their side will discolor and yours won’t, without this affecting the structural integrity of the structure.
Should you water seal your fence?
Wood is porous, so every time it gets wet, the water does a bit more damage to the fence. Instead of letting the elements take their toll, use a water seal to protect your fence and extend its life.
How often use Thompson’s water Seal?
Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.
Can you apply sealer with a pump sprayer?
Yes, you can use a standard pump garden sprayer to apply your sealant. Since solvent-based sealers have more active chemicals and corrosive agents, they are not recommended for garden sprayers. But if you’re using a water-based sealer, you can use the same sprayer you use for fertilizer and insecticide.
Can you apply Thompson water seal with a rag?
Use a dry microfiber cloth or rag to clean the surface. Keep in mind that using a damp microfiber cloth to clean the surface of an unfinished wood could warp. Add a drop of water on the surface to determine whether your wood is finished or unfinished.
How long does it take for Thompson water seal to dry?
Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson’s® WaterSeal® Waterproofing Wood Protector – Clear.
How long does Thompson Water Seal last?
Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
Can you put Thompson Water Seal on treated wood?
Some, like Thompson’s® WaterSeal® Waterproofing Wood Protector, recommend waiting 30 days before application on new pressure treated lumber. Other products, like Thompson’s® WaterSeal® Waterproofing Stain, can be applied immediately to new pressure treated lumber.
Can you apply Thompson’s Water Seal in the rain?
Thompson’s Water Seal, offers superb weather protection for bricks, mortar, stone & concrete. Its advanced silicone micro emulsion soaks in deep to provide long lasting protection against rain damage.
How much does a 5 gallon Thompson water Seal cover?
Sealed our deck (350 sq ft or so) and with the 5 gallon we’ll be able to seal it probably 3 more times entirely. Noticed minimal discoloration, but we do have a cover that keeps sun off for all but abour 4 hours at sunset.
How much area does a gallon of Thompson’s water Seal cover?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way. Thanks to its pigment-suspension technology, there’s no need to wait for the Waterpoofing Stain to have its turn in the paint shaker.
How many gallons does it take to seal a fence?
For a small fence, up to 175 square feet, you will only need one gallon of stain, in any transparency. If your fence is larger, up to 550 square feet, you will need to buy 2 gallons of stain. For very large fences, up to 700 square feet, you will need 3 to 4 gallons of stain to complete the project.
