QA

Quick Answer: What Is The Best Concrete Resurfacer

What is the best product to use to resurface concrete?

QUIKRETE® Concrete Resurfacer provides a beautiful, durable, wear resistant surface designed to withstand heavy foot and vehicle traffic. QUIKRETE® Concrete Resurfacer provides an economical alternative to removing and replacing existing old, spalled concrete.

How thick should concrete resurfacer be?

1 Unlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab. Concrete resurfacer is a very strong product, rated for compressive strength of about 4,500 psi.

How long does a concrete resurfacer last?

Thanks to its durability, concrete resurfacing can last a long time. Considering it’s been properly installed, well cared for and the existing concrete base is strong. A properly resurfaced floor can last from 10-20+ years.

How thick can quikrete resurfacer be applied?

One 40 lb (18.1 kg) bag of Re-Cap® Concrete Resurfacer will cover approximately 16 ft2 (1.5 m2) of surface at a thickness of 1/4 in (6.3 mm) or approximately 65 ft2 (6.0 m2) per bag when applied at the 1/16 in (1.6 mm) thickness with a broom or squeegee.

How do you get new concrete to stick to old concrete?

The most effective way to ensure a really good bond is with a scratch coat. This is simply a very wet coat made up by mixing the repair product with water. Mix up a small amount of the repair material to a soupy consistency. You don’t need to measure the water—just turn the stuff into slop.

Can you pour a thin layer of concrete over existing concrete?

How Thin Can You Pour Concrete Over Existing Concrete? The thinnest that is usually used when pouring concrete, in general, is about 2 to 2 ½ inches. That also applies to this pouring new concrete over old concrete. Any thinner than 2 inches would be too thin.

How many square feet does a 40 lb bag of concrete resurfacer cover?

One 40 lb (18.1 kg) bag of Concrete Resurfacer will cover approximately 17 ft2 (1.6 m2) of surface at a thickness of 1/4 in (6.4 mm) or approximately 90 ft2 (8.4 m2) per bag when applied at the minimum thickness with a broom or squeegee.

How long does concrete need to cure before resurfacing?

Continue moist curing for 24 to 48 hours prior to use. Under normal conditions, no special curing is required. Wait 24 hours before allowing foot traffic on the surface.

How do I make a concrete resurfacer?

Use 1 part cement and 1 part sand. Add water to the mix until it is the consistency of paint. This is used to coat the surface of the concrete right before you do the overlay coat. The mixture is thin enough to get down into the pores of the old concrete, as well as bond to the new.

How much does it cost to resurface a concrete slab?

The price of concrete resurfacing typically ranges from about $3 per square foot to $25 per square foot. However, the cost of your project will depend on a variety of factors. For our customers, cost is one of the most important aspects of a concrete resurfacing project.

What is the cheapest way to surface a driveway?

Of the four paving materials described in this guide, aggregate (gravel) is the least expensive, followed by asphalt, concrete, and paving stones. If you’re installing your driveway on a shoestring budget, gravel is your best choice.

Can you use thinset to resurface concrete?

Rough, damaged concrete can be made new again with thinset mortar. One method of concrete surface repair is to use thinset mortar to rebuild the top layer. Thinset mortar is a mixture of aggregates, cement and synthetic adhesives that make it bond to almost any clean surface.

How long does quikrete re cap last?

In addition to establishing a new standard for resurfacing concrete, QUIKRETE Re-Cap is packaged in an exclusive Weather Barrier Bag™ that will protect it from inclement weather and other harmful elements for up to eight months.

Does concrete overlay last?

Another factor is the preparation before applying the overlay. Common mistakes are failing to clean the concrete properly or to profile it adequately. With proper installation and maintenance, overlays are extremely durable and can last for decades, even in harsh climates.

What is BondCrete used for?

BondCrete contains an exclusive resin additive ensuring maximum bonding strength. BondCrete is suitable for Tiling, adhesive for craft work, patching of most surfaces, sealing concrete, rendering surfaces and most cement applications. BondCrete is widely used in the building and renovating industry.

What’s a bonding agent?

A bonding agent serves as the middleman between you and the surety provider (i.e., the insurance company) to determine which type of surety will best meet your needs.

What is the best bonding agent for concrete?

Epoxy Resin is known for being the most versatile of all concrete bonding agents. This bonding agent is ideal for high performance and lightweight parts. Characterized as being strong but brittle, Epoxy Resin can be formulated to become more flexible without losing its tensile strength.

Is quikrete as good as concrete?

To wrap things up, to answer the question is Quikrete as strong as regular concrete, the answer is yes. Quikrete has similar compressive strength to standard concrete mix once the curing process is complete, which takes place significantly faster for Quikrete.

How do you resurface over exposed aggregate concrete?

How To Cover Old Aggregate Concrete: 11 Ideas Option One: Use A Surface Coating. Option Two: Use A Matting System And Sealant. Option Three: Use A Cover System. Option Four: Add A Mulch Top Layer. Option Five: Add Pavers. Option Six: Cover With Thin Brick Strips. Option Seven: Paint It. Option Eight: Use Tiles.