Table of Contents
For shower-only controls, between 36 and 48 inches from the floor is common. Employ your helper to hold the fixture at an estimated height and then see if it’s a comfortable reach for all users.
How high should a shower valve be mounted?
The average height for a shower valve is 30-50 inches above the floor, though this is a general range. For tub-shower units, the height can be just a few inches about the tub or directly on the tub as part of the faucet.
How high should shower controls be UK?
Shower controls should be placed at a height 40”-50” (102-127 cm) above the shower floor and out of direct line of the water path to avoid being caught in extremely cold or hot water when operating.
How far back do you set a shower valve?
wall position, including tile (2-1/16″ [52mm]). The center line of the supply and discharge piping should be a maximum of 2-3/16″ (56mm) and a minimum of 1-7/16″ (37mm) behind the finished wall surface.
Should shower valve be centered?
Re: Correct location of shower head/shower valve All plumbing is typically centered in the space. You’re splitting hairs whether that is inside the curb to the wall or from the shower door glass to the wall.
How much room does a shower valve need?
The shower valve should be 12 inches apart. The next stage of the project will be aided by a small mark at the center of the plates, in line with where you expect the shower valve and faucet to be. On either side of the midpoint, mark 6 inches.
What do you do when your shower valve is deep?
If your shower valve was installed too deep, you may need to purchase a shower valve extension. Signature Hardware carries valve extensions for some rough-ins, but not all. Professional installation should factor in the correct depth behind the wall, with any exterior wall covering included.
How much space should be between shower valve studs?
Stud Spacing Your goal is to center the shower valve between studs 12 inches apart. A little mark at the midpoint of the plates, in line with where you expect the faucet and shower valve to be, helps for the next stage of this project. Next, mark 6 inches on either side of the midpoint.
Do all plumbing walls need to be 2×6?
All plumbing walls shall be 2 x 6 studs (minimum) in single family dwellings and townhouses. It shall be the plumber’s responsibility to notify the general contractor when 2 x 6 walls are not provided for plumbing, and to have the proper framing installed before proceeding on any further work.
Do I need a rough-in valve?
A Rough Valve is a REQUIRED PART OF EVERY SHOWER. It mixes hot and cold water to create warm water suitable for your shower. Most shower rough-in valves have 4 ports. 2 inlets for the hot and cold water pipes, and two outlets, one for tub spout and one for showerhead.
How far from Wall should shower head be?
Typically, a wall-mounted or fixed shower head should be about 3 to 4 inches from the wall. If you angle the shower arm at 100 or 120 degrees, you’d have enough space to move around your bathing enclosure without bumping against the wall.
How far should shower head be from floor?
The ideal height range for the shower controls is between 40 to 50 inches above the floor. You can lower the controls slightly if you’re constructing a seated shower. Getting the shower head height right can make a huge difference. It can determine how comfortable the shower is to use.
Why does Moen shower handle sticks out too far?
There are two reasons why your Moen Shower Handle may stick out. One might be because the valve wasn’t placed properly on the wall. Another one is the Moen Shower Handle which has had this problem for 5-6 years. In this case, the valve body is fitted with the plaster ground flush with the completed wall.
What is an escutcheon plate?
An escutcheon is a type of plumbing supply typically made of metal that hides the unsightly hole in the wall that pipes usually come through. People can also refer to them as flanges or cover plates. Without them, the bathroom or sink would look unfinished, with big gaping holes in the wall around your pipes.
Are interior walls 2×4 or 2X6?
Modern conventional home building normally makes use of 2×4 lumber (top line above, second from left) in constructing exterior walls. But 2×6 framing, which is a little more than 1.5 times wider, is a common upgrade and is required by some local building codes.
What kind of valve do I need for my shower?
Pressure balancing valves, also called mechanical or anti-scald valves, are the most common types of shower valves. A pressure balancing valve is designed to rebalance the water pressure to keep the shower from becoming excessively hot.
Can you use a shower tub valve for shower only?
Can a tub and shower faucet be used just for a shower? Most tub and shower combination faucets can be installed in a shower without using the tub spout. If you do not wish to use the tub function, you can plug the outlet for the tub spout on the valve and not install the spout on the tub wall.
