Table of Contents
What size is my lazy Susan?
When deciding what size lazy susan you need for your cabinet, you need to measure the inside depth of the cabinet from the back wall to just inside the door frame. Then, measure the inside width of the cabinet from left to right.
How do you measure a lazy susan door?
Measure from one inside edge of your cabinet opening to the corner of the opening (where your two doors will meet), then measure from the corner to the other inside edge of the cabinet opening.
What are the dimensions of a lazy Susan base cabinet?
Lazy Susan Base Cabinet Dimensions: 33-36″ Wide, 34.5″ Tall, 24″ Deep.
What are the dimensions of a 36 Lazy Susan cabinet?
x 34.5 in. x 24 in. Shaker Base Lazy Susan Cabinet in White.
How do I measure for a corner cabinet?
Measure from the corner of the wall to the outside edge of the base cabinet on the right side of the corner cabinet. Use a tape measure to get an accurate measurement of the distance. Measure from the corner of the wall to the outside edge of the cabinet on the left side of the corner cabinet.
How much is full overlay?
A Full Overlay door will overlay that same 1.5” face frame 1.25”, leaving a ¼” reveal on the sides (stiles) and bottom (rail).
How do you measure a full overlay door?
Overlay refers to how much the door overlaps on the hinge side. You can determine this by measuring the width of the door, subtract the width of the opening and divide that in half. For example, if the door is 1” wider than the opening, that means it overlays 1/2″ on each side, so you would select 1/2″ overlay hinges.
What is the overlay measurement on a cabinet door?
The overlay is the amount or distance that the cabinet door overlaps the cabinet opening on the hinge side of the door. Normally, this distance is the same on both sides of the cabinet opening and will range from 3/8″ to 1-9/16″.
How do you read cabinet measurements?
The tall cabinet width is always listed first and height is always the last two numbers. Thus 24″ is the width and 90″ is the height. Since most tall cabinets are 24″ deep we only list the cabinet depth when it is not 24″ as in the following example.
How much space should be between upper and lower cabinets?
The standard distance between the top of a kitchen counter and the bottom of the wall cabinets above it is 18 inches. For the average person, this distance is the ideal balance between plenty of space to work on the countertop and the ability to reach all of the shelves in the cabinet.
What are the dimensions of a kitchen cabinet?
Base Cabinet Height, Depth, and Width Height, without countertop 34 1/2 inches Height, with countertop 35 to 36 inches Depth (front to wall), without countertop 24 inches Depth, with countertop 25 to 26 inches Standard widths 12, 18, 24, 30, 33, 36, 48 inches.
What is the standard size for a kitchen sink cabinet?
A 30-inch wide or a 36-inch wide cabinet are most common. The height of the cabinet can be customized, but 36 inches is average. A typical 33-by-22-inch sink will fill a 36-inch base cabinet.
How do you measure an upper corner cabinet?
How to Measure Corner Cabinets Place the end of the measuring tape at the back of one side of the cabinet, right next to the corner. Repeat the process, but start the measurement from the other side of the corner. Place the end of the tape measure against the back edge of the cabinet, along one of the ends.
What is the size of a corner kitchen cabinet?
BASE CORNER CORNER They come in many sizes, the most standard being 33”, 36”, and 39” and can be hinged either right or left. Larger BCC cabinets have wider openings, which improves accessibility to the inside and smaller ones will have the opposite, so keep that in mind when planning.
What are the dimensions of an upper corner kitchen cabinet?
The average wall or upper kitchen cabinets are 30”-42” in Height, 12”-24” in Depth, and 9”-36” in Width.
How do I measure for replacement cabinet doors?
How Do You Measure for Single Cabinet Doors? Remove the door you want to measure. Measure the opening from top to bottom, and then left to right, then write down the exact width and the exact height of the opening. Then add in your overlay.
How do you measure a frameless overlay cabinet door?
To measure for full overlay cabinet doors on frameless cabinets, the cabinet door needs to be 1/8″ smaller than the cabinet on all sides. So first take a measurement of the cabinet opening, then subtract 1/8″ on all sides.
What is full overlay vs half overlay?
Overlay cabinets can have a full or partial overlay. Full overlay doors and drawers cover the face frame of the cabinet completely. Partial overlay cabinets cover most of the cabinet frame but leave space between the drawers and doors.
Is full overlay the same as frameless?
Frameless cabinets only offer one overlay style, Full Overlay. The Full Overlay of a frameless cabinet completely covers the entire box, leaving only a 2mm reveal that creates a sleek, seamless appearance, making it a popular choice for modern and contemporary styled kitchens.
What is a cabinet door overlay?
Cabinet overlay means the correlation of your cabinet doors to the cabinet face frames. This overlay affects how much of the cabinet frame shows and can change the appearance of your space from traditional to a contemporary-style kitchen.
What is standard cabinet overlay?
Standard overlay cabinets (also called traditional overlay) tend to be less expensive and do not require hardware because there is enough finger space on the side of the cabinet door or drawer face. They also have more exposed face frame, with at least 1 ¼ inches on all sides of the doors and drawers.
How do you measure for kitchen cabinets?
Tips for Measuring Your Kitchen Ensure accuracy. You’ll need a tape measure, straight edge and graph paper. Measure clockwise. Record the overall length of each wall, working to your right around the room. Get the width and height. Find your center. Include the trim.
How do I identify my kitchen cabinets?
Cabinet brands that belong to the Kitchen Cabinet Manufacturers Association (KCMA) will have a sticker on the back side of the sink door or side wall of the cabinet. On the sticker there should be a code or the cabinetry name in the middle of the label.
