Table of Contents
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
What is the best material for soffit and fascia?
The Materials You Choose Matter, Too Most roofing and siding professionals recommend that you go with either aluminum or vinyl for your fascia and soffit, as both are more water-resistant, and neither are as prone to rot.
What is the best timber for fascia boards?
Timber: Popular hardwood and softwood timber species for fascia board are western red cedar European oak, Utile, Iroko, Douglas fir, Larch and Accoya. The latter is an extremely durable sustainable option. All types can be available FSC certified and suitable for domestic applications.
How thick should fascia boards be?
Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction.
Should I use treated lumber for fascia board?
Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.
Is Hardie board good for soffit?
HardieSoffit® panels are 8 ft. and 12 ft. long, ¼ in. thick factory-primed fiber-cement panels designed to be used on the underside of eaves as soffit material.
Should I use vented or solid soffit?
Vented Soffit Panels Increase Air Circulation Due to the small perforations, vented soffit panels increase the air circulation of the attic area. Solid soffit panels, on the contrary, effectively seal off the attic space from fresh air, causing the air inside to become trapped and grow stale.
Can plywood be used as fascia board?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
What is the board behind the fascia called?
Soffit is the layer of wood, vinyl or aluminum that extends from the bottom of the fascia to the top piece of your wall board. Together, they protect the rafters from weather, moisture, and allow air to flow through soffits and vents.
How wide should a fascia be?
Standard gutter size for residential homes is five or six inches. At the backside of a 5 inch gutter, the fascia board mounting area will be four inches tall. On a six inch gutter, the mounting area is 5 inches.
Can you use 2×6 for fascia?
Around here everyone uses 2×6 fascia and then covers it with aluminum fascia. If you are leaving the fascia as wood to be painted then the finished face board is better to wider. So you could use 2×4 frame work and 5/4 or 1×6 fascia boards.
What kind of wood do you use for soffit and fascia?
Although unsanded and touch-sanded grades of plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
How thick is HardieSoffit?
HardieSoffit® panels are 2,438mm (8 ft) and 3,658mm (12 ft) long, 6mm (¼ in) thick factory-primed fiber-cement panels designed to be used on the underside of eaves as soffit material. HardieSoffit panels are available as vented or non- vented boards.
Can you use cement board for soffit?
For ventilated soffit applications, the cement board product is available in perforated sheets, for non-ventilated, solid sheets are available.
When should you not use vented soffit?
While soffit comes in wood and aluminum, they are most commonly made of vinyl for durability. Soffit can be non-vented or vented to allow for maximum roof ventilation. Non-vented or continuous soffit works best when your roof has narrow eaves or if you need to ventilate a large amount of attic space.
Can you have too much soffit ventilation?
You can’t have too much soffit venting, but it’s worth noting the minimum requirements. Usually, 4-in. by 16-in. soffit vents are rated for 26 sq.
What material is used for soffits?
Soffits come from different materials. Some come from woods while others are made of uPVC, wood, aluminum, steel or fiber cement. The first material for soffits is wood. If you want to have an old look for your house, you may choose wooden soffits.
What type of wood is used for eaves?
All About Eave Eaves are simple boxes. The bottom — or soffit — where the damage is, is typically thin plywood, usually 1/4-to-3/8-inch-thick. It’s cut in long sections and butt-jointed together with a thin piece of plastic molding that slips over both ends forming a joint.
What do you use for fascia on a deck?
If you choose to add fascia, any kind of pressure-treated or otherwise rot-resistant lumber can be used. However, if you’ve opted for synthetic decking in one of the many colors available, you’ll want to consider using a complementary PVC fascia. PVC fascia typically comes in 1/2-in.
Can you use Douglas fir for fascia board?
Douglas Fir will work for interior or exterior applications. Great for trim, fascia, overhangs, soffits or rustic-look siding. Clear Douglas Fir is an excellent choice when the finest appearance is required.
