QA

How To Install A Hot Water Recirculating Pump

Are hot water recirculation pumps worth it?

A hot water recirculating pump will save you money, especially if you have a larger family. A family of 4 with normal water usage can expect to save $50-$75 a year. Since pumps cost about $200 each, the recirculating pump will pay for itself in 3-4 years. .

Where should a circulating pump be installed?

Standard good practice among heating techs is to install the circulator pump on the return side of the loop where cooler temperatures can extend its life.

How do you install a hot water recirculating pump under the sink?

How does a hot water recirculation work?

This system creates a loop from the water heater to the faucet and back again. The unused hot water is drawn back through this loop by the pump, so when you turn on your hot water faucets, you get hot water quickly. Water is not left in the pipes to get cold and you waste less water because you don’t have to wait.

Do recirculating pumps wear out pipes?

In most cases, though, the primary, or even sole, culprit is excessive flow velocity. In an effort to ensure instantaneous delivery of hot water, an oversized pump has been installed, with the result that the pipes are literally eroded away by their own contents.

How much does it cost to run a recirculation pump?

This pump works with under-sink systems with large hot-water tanks and tankless heaters. The cost of the electricity at $0.12 per kW for the small pump for 250 feet of pipe on a timer for eight hours a day with a sensor and switch that runs on average 3 minutes per hour and costs $1.40 to $1.59 a year in electricity.

Should a circulation pump be on the flow or return?

The best place for the pump(s) is still on the flow side. This keeps the bulk of the system under positive pressure from a combination of the pressure imposed by the system water connection, and then when the pump is running, the pressure provided by the pump.

Does a circulator pump push or pull?

The pump pulls water in through the inlet and pushes it out through the outlet. Typically, there will be an arrow on the casing to identify the direction of flow so you know which is the inlet and outlet.

How many circulating pumps do I need?

1 GPM = 10,000 BTU/hr, meaning that for every 10,000 BTU’s of heat load the circulator must output a 1 gallon per minute flow. Assuming that system calls for 100,000 BTU/hr, a circulator pump should have a minimum 10 Gallons Per Minute flow rate at a given pressure drop.

Do you need a check valve on a recirculating pump?

Whenever a zone connects to the main piping in the recirculation system, a check valve is required. A proper design will have a flow control valve installed at the end of the zone to regulate how much water goes through that zone.

How do I stop wasting water waiting for hot water?

Check out the best ways to reduce your wait for hot water below. Insulate Your Hot Water Pipes. Flush Your Water Heater Tank Routinely. Install One or More Tankless Water Heaters. Install a Recirculation System.

Will a recirculating pump prevent freezing?

Install hot water recirculating pump. Installing a hot water recirculation system helps ensure that you always have hot water in your taps and prevents pipes from freezing during the winter.

Do circulator pumps run all the time?

So depending on where you live and how your heating system is designed and controlled, it may be normal for the circulator pump(s) to run continuously.

Can I use a hot water recirculating pump with a water softener?

Answer: Yes. As long as you have a return line running back to your water heater. You do not need a separate return line at every faucet.

How long do hot water recirculating pumps last?

How Long Do Recirculating Pumps Last? Most pumps – assuming you did not get a lemon – will last 10 to 15 years. The biggest factors that impact their life expectancy are the amount of water you use every day and the quality of the manufacturing.

Do recirculating pumps use a lot of electricity?

Secondly, hot water recirculation pumps use a decent amount of energy – this also needs to be factored into potential savings. A pump that consumes 25 watts of power would use around 200 kWh of electricity each year. The average price of electricity in the US and Canada is $0.13 per kWh and $0.17 per kWh, respectively.

Do hot water recirculation pumps use more gas?

Recirculation systems that operate continuously have the potential to use more energy, due to energy spent pumping and hot water energy lost from the pipes, than the energy saved by reducing hot water waste.

How much does hot water recirculation cost?

Without the need for extra piping, this type of hot water circulation pump system also comes at a much lower cost. Depending on the size of the pump and installation difficulty, the average cost of a hot water recirculation pump costs anywhere from $200 to $800 (installed).

Which should be hotter flow or return?

Why Temperatures Differ Between the Flow and Return Water You’ll notice that the flow heats up quickly, and is usually hotter than the return pipe. This is because all pipe work and radiators are cold when you fire up a boiler. The pipes and rads absorb some of the heat, so the return water coming back is cooler.

Where is the circulator pump on boiler?

Central heating circulating pumps are usually located inside or near your boiler, or in your airing cupboard next to your hot water cylinder.