Table of Contents
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
What would cause a washing machine not to drain?
There are a few possibilities why your washing machine won’t drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do you force a washing machine to drain?
If not, follow these steps: Step 1: Turn off the power and lay down towels. For safety, unplug the machine. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
Why is my GE washer not draining or spinning?
If the washer drains properly, then the clog has likely cleared. If water remains in the washer, check for a pinched or flattened drain hose. You may even need to disconnect power to the washer and remove the drain hose from the back of the machine and the plumbing to see if there is a clog inside the drain hose.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
How do you fix a washing machine that won’t spin or drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
How do I force my GE washer to drain?
Here’s how to do it. TURN OFF THE POWER. Unplug the washing machine from the power outlet. REMOVE LAUNDRY. Take out any clothing that’s in the washer tub. EMPTY THE TUB. Use a bucket to scoop the water out of the washer tub. MOVE WASHER AWAY FROM THE WALL. DISCONNECT DRAIN HOSE. PINPOINT THE ISSUE.
How do I get my GE washer to drain and spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
How do you reset a GE washer that won’t spin?
Motor Reset Procedure: Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
Can you pour Drano down washing machine drain?
Can I put Drano down my washing machine drain? Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry before normal use.
Where is the drain pump on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
How do I know if my washing machine drain is clogged?
The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.
Why is my washing machine drain backing up?
The p-trap is clogged As water flows through it, sand, lint and other things sink to the bottom of the U. This helps prevent clogs further down the line. If the p-trap gets too full and clogs, it can make your washer back up.
How do you reset a GE washing machine?
Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.
Why does GE drain and spin add water?
Drain & Spin, on most models, will add water for a couple of seconds. This helps balance the load and is normal.
Why won’t my GE washer drain?
A kink or clog in your washing machine’s drain hose could be interfering with water flow and preventing your machine from draining properly. To inspect the drain hose, turn off the power to the washer, disconnect the hose (have a bucket ready to catch any water), and check the hose for damage or obstructions.
