Table of Contents
Heat the dented area of your vehicle with a hair dryer at the highest setting possible. Get it as hot as possible and then use a can of compressed air to blow on the dent. The cold air will contract the plastic and allow the dent to pop out on its own.
How do you pull a dent out yourself?
Five DIY methods for removing dings, dents from your car Try the plunger method. You know how powerful a plunger can be with your plumbing problems? Use hot water for dented bumpers. Bumper plastic is hard for good reason. Hammer out the dent. Pop out the dent with a hair dryer and compressed air. Buy a dent removal kit.
How can I pull a dent out of my car?
First, heat the dent with the hairdryer approximately six inches away for about 30 seconds. Then cover the dent with a piece of aluminum foil and rub dry ice over it. The rapid change from hot to cold should make the dent pop out within a minute or so. Another temperature trick involves boiling water.
Can you push a dent out from the inside?
If your dent is in a plastic surface like a front or rear bumper cover and you can get to its inside surface, you can pour boiling water over the area to soften it up, then push the dent out from the inside. If you can’t access the dent from the inside, try using a hair dryer to warm up and expand the outer surface.
How do you get a dent out of metal?
Boiling Water: Simply pouring boiling water over the area can be enough to pop a small dent out of your car in many cases. That’s because the built-up stress in a dent is relieved when you apply heat and the metal or aluminum can relax enough to pop back out to its original shape.
Do dent pullers work?
Dent pullers only work on shallow dents on flat, flexible surfaces. They can improve the appearance of dents but probably won’t create a perfect finish. But these tools will not work on deep, angular dents or damage along the edges of bodywork.
Will boiling water damage car paint?
The heat makes the metal more expandable and malleable, allowing it to be pushed and pulled easily. Pouring hot water over metal also has its problems. It could warp the metal out of shape, make it less sturdy; it could even ruin your paint job if your paint isn’t up to par.
Can you plunge a dent out of a car?
You’ll need a pot of very hot water and a simple plunger. Pour the hot water over the dented surface of the car. Put the plunger over the indented area and pull straight out. Your dent should pop right out.
Can you push a dent out by hand?
Just heat boiling water and pour it over the affected area. Reach your hand behind the dent and push it out with your hands. The plastic should be soft because it is warmed up and will be able to release the dent more easily.
What kind of dents can be popped out?
The dents which form a big depression on a body panel and not sharp indents can be pulled out. If there are cracks on the dented panel, the dent can most likely not be pulled out. Very large dents can not be suctioned out. If the body panel is made of aluminum, the dent cannot be pulled out in the majority of cases.
How much does it cost to have a small dent removed?
The dent repair cost may range from $50 to $2,500. Although that’s a broad range, most small dents that are roughly an inch in size may cost around $50 to $125. Small indentations may come from a flying rock or piece of hail. Dents stemming from a collision are typically larger and cost $150 or more.
Should I worry about a small dent in my car?
Reduced resale value. Things like unrepaired dents can lower the value of a used car, even if they’re small. Add paint damage and rust spots to these car dents, the price a buyer is willing to pay goes down even more.
Can you remove a dent with hot water?
Use boiling water Simply boil water in a teapot, protect yourself from burns with rubber gloves, and have a pot of cold water on hand. Then, pour the hot water from the teapot over the dent. Before it cools down, pop the dent out from the inside.
How do you remove hailstorm dents?
The quick change in temperature should cause the dent to pop out within a few minutes. Lay a cold, wet cloth over the dent. Get a washcloth wet in cold water and lay it over the dent for several minutes. Spray compressed air over the dent. Apply dry ice to the dent.
Can you hammer a dent out?
Using a Standard Hammer Most metal hammers will do nothing more than dent, scratch and compromise the body of your vehicle. It’s very easy to make things worse with a standard hammer. Instead, professional bodywork hammers come in a range of head shapes and sizes to handle a variety of dents.
