Table of Contents
You will use approximately 55 screws per 3′ x 5′ cement board and 91 screws per 4′ x 8′ cement board. In ceiling applications, screws should be placed every 6″”.
How many screws do you need for Hardie board?
Fasten a minimum of 12 screws into the board (4 rows of 3 screws). Keep fixings between 15mm from board edges and 50mm from board corners.
How many screws are in a sheet of HardieBacker?
Screw the HardieBacker into the floor, using 1¼-inch backerboard screws and using one screw every 8 inches. Offset the interior screws so they are staggered with the outer screws, and make sure no screws are closer than two inches from the edge.
How far apart should screws be in HardieBacker?
Fasten HardieBacker cement board with specified nails or screws (as listed in “Materials Required”) every 8 in over the entire surface. Keep fasteners between 3/8 in and 3/4 in from board edges and 2 in from board corners.
How far apart should cement board screws be?
Secure Backer Board with Screws Drill cement board screws through the backer board sheets every 6 to 8 inches. Position the screws at least 1/2-inch, but no more than 2 inches, from the edge of the sheet.
Can you put screws in Hardie board?
Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.
Can I just screw down cement board?
Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.
Do you have to tape seams on Hardibacker?
For tile backer boards such as Durock, Wonderboard, Hardiebacker, Permabase, and others the seams between the board need to be treated with 2-inch alkali-resistant mesh tape.
Do you need thinset under Hardie board?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.
Can you tile straight onto Hardibacker?
HardieBacker can take up to 200kg of tile hanging weight per m2 so almost any tile can be fixed. Once secured cover the joints with Alkaline-resistant tape and feather the tile adhesive to leave a 150mm wide joint.
How many screws do I need for a 3×5 cement board?
In floor applications, screws should be placed every 8″”. You will use approximately 55 screws per 3′ x 5′ cement board and 91 screws per 4′ x 8′ cement board. In ceiling applications, screws should be placed every 6″”.
What is the difference between durock and Hardibacker?
Durock is a reliable cement product that contains glass mesh. It is the heavier of the two materials, which means it is more difficult to use and maneuver. HardieBacker is much more light, and it is also the best selling brand of cement board available. It is much cleaner because it does not have any glass in it.
What do you fasten Hardie board with?
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
Do you use nails or screws for Hardie siding?
Hardie board comes with a 30-year manufacturer’s warranty, but that means you need the nails to last at least that long too. James Hardie recommends that nails be hot dip galvanized (at a minimum) or stainless steel (as a best practice).
What kind of screws do you use for Hardie board siding?
James Hardie recommends 1-1/4” long galvanized or STAINLESS steel roofing nails or 1-1/4” long ribbed waferhead screws in compliance with the tile industry. It is 8-18 x 3/8” HD.
What do you do with a gap between tub and cement board?
Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub.
What kind of thinset goes under cement board?
An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.
Should I wet Hardibacker before tiling?
A. To be more precise, I’ve installed lots of concrete backer board for years, all with good results. The concrete is unaffected by any water that manages to get behind the ceramic tile. If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to.
Can I use drywall mesh tape for cement board?
Apply Mesh Tape Paper tape simply won’t hold up on cement board. Although paper tape generally leads to a cleaner finish on drywall, you can still achieve a smooth look if you use mesh tape on a drywall/cement board joint. Use this self-adhesive joint tape where cement board and drywall meet.4 days ago.
Do you need to waterproof Hardibacker?
Hardiebacker (James Hardie): the use of a waterproof membrane, vapor barrier or vapor. retarding membrane is optional unless the local building code requires it.
What happens if you don’t put thinset under Hardibacker?
It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps. The installation manual for HardieBacker suggests to embed it in thin-set and it should be installed over plywood.
