Table of Contents
uL. (none) Unbalanced load. uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.
How do I fix my uL washing machine?
UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.
How do you fix a uL code on a Whirlpool washer?
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
What is uL code on Maytag washer?
uL is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a mini-cycle to rebalance the load. Display clears if mini-cycle successfully rebalanced the load.
How do I fix the uL code on my Kenmore washer?
You can try to clear the Error Codes; Unplug the washer for 1 to 2 minutes. Disconnect the U.I. (touch pad). Plug the washer back in for 1 to 2 minutes.
How do I fix the code on my Whirlpool Cabrio?
Always disconnect the washing machine’s power supply before working on the appliance! First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.
Why does my washing machine keeps unbalancing?
The most likely culprit is the suspension rods. These rods help to limit the amount of side to side and front to back movement that happens when a washer enters the spin cycle. If your washer is manifesting the banging noise of an unbalanced load with every spin cycle, contact us today.
Why does my Whirlpool washer keep getting off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
Why is my Whirlpool washer not filling up with water?
If the water inlet valve is defective, the wash may fill slowly or not fill at all. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
How do you balance a Maytag washer?
Place a 4-foot level across the front top of the washer. Adjust the front legs if necessary until the front is in balance. Loosen the retaining nut with the adjustable wrench and turn the feet as necessary until the front balances. Tighten the nut with the adjustable wrench.
Why does my Maytag washer get out of balance?
Common solutions for: Maytag ob – Off Balance Washer vibration can occur if one or more of the shock absorbers is broken or worn out. Check the absorbers to be sure they are installed correctly and in the right position. Sometimes when a washer is moved the shock absorbers separate and have to be put back together.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
How do you reset the sensor on a Kenmore washing machine?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
How do I reset my Cabrio washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
Is there a reset button on a Whirlpool Cabrio washer?
Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
Why won’t my Whirlpool Cabrio washer drain and spin?
The most common causes of a Whirlpool Cabrio not spinning are: Defective lid switch. Broken drive belt. Loose drive pulley nut.
Why does my washing machine make a banging noise when spinning?
If your washing machine makes a loud rumbling or repetitive banging sound, which is particularly bad on a spin cycle, then it is most likely due to loose or worn out drum bearings.
How do I know if my washing machine balance ring is bad?
The balance ring is filled with fluid. This fluid helps to dampen the vibration of the washer. If this fluid leaks out of the balance ring, the washer tub will vibrate and shake during operation. Check the balance to determine if is still filled with fluid.
