Table of Contents
Should shower drain be flushed tile?
Yes, the shower floor’s drain should be flush with the tile around it at the point where the two meet. In any case, the drain should be at the lowest point of the shower but still flush with the tile at the drain and tile meeting point.
How high should shower drain be for tile?
2″ Drain Pipe should be centered in a hole (approximately 5″ diameter) in the flooring. The top of the Pipe should be no higher than, and no more than 1/8″ lower than, the top surface of the floor on which the base will be set.
Do you grout around shower drain?
Grout fills the gaps between tiles creating one surface. You can seal around the grout using regular grouting procedures and must do so to ensure the 1/4-inch space between the shower drain and the tiles creates one continuous flat surface from drain to tile.
What is a shower drain flange?
A bathtub drain flange is the finished drain part that’s visible in the tub. Some manufacturers refer to the drain flange as a “drain body” or “drain basket”. Between the underside of the flange and the tub surface, there’s a good amount of plumbers putty that seals the inside of the drain.
How high should a shower drain be from the floor?
Getting Started. Make sure your drain pipe is at the appropriate height (approximately 1/4 inch above your concrete or subfloor).
How thick should mortar be at shower drain?
The shower pan base mortar layer thickness should be approximately ½ to 1 inch thick. Since the shower floor already has a pre-slope, just apply a base mortar layer that has an even thickness throughout the shower floor area.
Where should the shower drain be located?
Point drains ideally sit in the middle of the shower floor or by the end of the wall. Either way, the water drains downward by a slope in the bottom. When placed by the wall, the floor is sloped sideways.
Should I grout between tile and shower base?
Grout is generally the best choice for filling joints between tiles in showers or elsewhere. Grout in these particular seams is more likely to crack due to settling. Some tile setters fill these seams with matching color caulk because it’s more flexible should movement occur.
Can I use caulk instead of grout in shower?
Caulk is used to waterproof joints for space like bath tubs, showers, windows etc. Caulk is strong enough to adhere to tile surfaces without crevices. Caulk may shrink or dry out over time, which is why it shouldn’t be used in large installations or as a replacement for grout.
Does a shower drain need a vent?
It’s easy to forget, but it’s a vital and required part of any plumbing fixture drain. The vent pipes remove sewer gases while allowing air into the system to help the water drain. Without a vent, your shower won’t drain correctly.
How do I install a shower drain with no access from below?
How to install shower drain without access below: Remove the existing shower drain. Measure and cut the assembly parts. Clean the area and pipes. Assemble and install the new drain. Apply a sealant and tighten the shower drain. Clean excessive sealant. Install strainer cover. Conduct a leak test.
How do you Slope a shower floor for a linear drain?
Both center pitch drains and linear drains require a gentle ¼” slope per foot, but the difference is in the effective angle that the slope creates.
Where does a linear shower drain go?
As a general rule-of-thumb, linear drains are located at either the back or side wall of where the fixtures are installed, or along the threshold or entrance.
How far should shower drain be from wall?
Discharge hole (vertical): Drain located at floor height; distance is zero. Fixture (side to side buffer): Measured from center of the toilet to either side, minimum. clearance is 15 inches to any wall or other fixture; 18 inches is recommended if the bathroom layout allows for this.
What size tile is best for shower floor?
Bathroom Tile Size Advice: Floors, Walls, Showers & Tubs Area Recommended Sizes Small shower floor 1-inch square Small shower walls 1-inch square to 4-inch square Moderate or large shower walls 4-inch to 15-inch by 30-inch Bathroom floor 1-inch square to 12-inch square, or up to large-format.
How thick is a tile shower floor?
Measure and note the thickness of the tile to be installed on the shower floor. Typically, ceramic tiles are approximately 1/4 inch thick, and marble, sandstone or paver tiles may be up to 1/2 inch thick. Minor deviations in thickness are compensated for by using more or less thin-set mortar when installing the tiles.
What kind of mortar do you use for a shower pan?
The ideal mortar for a shower pan is a mix of standard cement mix with sand and Portland cement. This type of mortar creates a great water-resistant barrier that can support the weight of the shower unit.
How thin can a mortar shower pan be?
Thin-set mortars are typically about 3/16”, which makes it preferred when height is an issue (e.g. barrier free showers). When tile is bonded to the subfloor with a thin-set, movement in the subfloor can telegraph through the tile and cause it to crack.
How thick is thinset for shower floor?
Plan for a layer of thinset 3/16-inch to 1/8-inch thick beneath your tile. A 3/16-inch layer of thinset will be enough for tiles with a smooth back to bond the tile to the floor or backer board. For natural tiles with an uneven surface on the back, you may need to spread a 1/8-inch layer of thinset during installation.
Does it matter where the shower waste is positioned?
technically, the trap far away from shower exit as possible to prevent slipping in water when exiting. pratically, nearest place possible for trap maintenance.
