Table of Contents
How much does an ignitor for a furnace cost?
A furnace ignitor replacement costs $100 to $250 on average. Most universal hot-surface ignitor prices are $15 to $35 for the part alone.Furnace ignitor cost. National average cost $175 Minimum cost $90 Maximum cost $400 Average cost range $100 to $250.
Are furnace ignitors universal?
This universal ignitor is a replacement part for use in gas-fired appliances like furnaces, water heaters, and boilers, compatible with over 150-OEM models.
How long do furnace ignitors last?
No matter which type of ignitor is in your furnace, this chain of events lights your heater so that it blows hot air. Don’t worry—an ignitor that goes bad is common for most furnaces. Fortunately, you can replace the ignitor without replacing the full furnace. Most ignitors last about seven years.
How do I know if my ignitor is bad on my furnace?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
Can I replace the igniter on my furnace?
The igniter is a small and brittle component that can easily break. You can choose to replace the igniter on your own, but you must instead call a repair technician to avoid costly mistakes. HVAC contractors will gladly replace the igniter and perform your furnace yearly maintenance at an affordable price tag.
Are all furnace ignitors the same?
Most ignitors are interchangeable as long as they fit in the furnace space provided. Select your ignitor by looking at the one you have, and comparing it to the photos of ignitors here; select the one most similar.
Does Menards sell furnace igniters?
PROTECH Water Heater Hot Surface Ignitor at Menards®.
Can you clean an igniter on a furnace?
If your furnace has a spark ignitor and it’s working haphazardly, it too could be covered with soot, and a blast of compressed air may be enough to clean it. Compressed air can also clean a blocked pilot tube that is causing the pilot flame to burn weakly or not at all.
What causes furnace ignitor failure?
As mentioned above, sometimes the cause of a furnace ignitor failing to ignite is due to a safety issue, such as a clogged air filter, for instance. So, if your furnace is failing to ignite, it’s a good idea to check the air filter. If it looks clogged up, then this is probably the source of the problem.
What causes a furnace ignitor to crack?
Electrical Issues A power surge may negatively impact the ignitor and cause it to short-circuit. Most heaters may handle a range between 110 and 125 volts of electricity supply. Anything above that may cause the ignitor to fail.
Why is my furnace ignitor not working?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
Why is the furnace blowing cold air?
A clogged filter is one of the leading reasons for a heater blowing cold air. But even if you swap the air filter with a brand new one, dirt and debris can still be found within the unit. This could eventually lead to overheating. If your furnace looks pretty dirty, call an HVAC provider for a professional clean.
Where is the ignitor switch on a furnace?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
How often should furnace ignitor be replaced?
According to the Gas Furnace Guide, ignitors have an average lifespan of four to seven years. So, after about seven years, you may have to replace the ignitor; however, you probably won’t have to replace the entire furnace because other parts, such as the heat exchanger, can last more than 15 years.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
Can you light a furnace with a lighter?
Use a long lighter to light the furnace pilot light. Once it’s got a flame, which can take about 30 seconds, you can release the reset button. Once the furnace pilot light has a steady flame, you can turn the switch on and adjust the thermostat to the desired temperature.
What are the four different types of igniters on a gas furnace?
Types of Furnace Ignitors Direct Spark Ignition. Direct spark ignitors have no standing pilot lights. Intermittent Pilot Ignition. The Intermittent pilot ignition has a pilot light that lights only when the thermostat calls for heat. Hot Surface Ignition. Mercury Bulb.
Which is correct igniter or ignitor?
As nouns the difference between igniter and ignitor is that igniter is any device that is used to ignite something, especially a fuel mixture, or a charge of explosive while ignitor is .
Are all hot surface ignitors interchangeable?
And each brand has different models. Within the same brand they might be more similar but no guarantee. And what makes matters worse is that the igniter you are replacing is probably broken. So if it was a hot wire igniter you won’t be able to compare the resistances to a new one to see if they might perform similarly.
Does Menards sell limit switches for furnaces?
Mr. Heater High Limit Switch (HS35FA/HS170FAVT/MH400FAVT) at Menards®.
