Table of Contents
Can you install drip edge after gutters?
If the overlap is too short, fix it by placing drip edge under the first row of roof shingles and be sure that the exterior edge is reaching over the gutter. If the gutter is lower than the bottom edge of the drip edge, install flashing behind the drip edge and over the back edge of the gutter to remove the gap.
Do I need drip edge with gutters?
If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.
How far below drip edge should gutters be installed?
A safe distance between the gutter and the roof edge should be between 2 to 3 inches. If the gutter distance is more than 3 inches, the rain will run off the roof and won’t drain properly.
Can you install new drip edge over old drip edge?
Replacing Drip Edge Eave Strips: Align one end of the lower eave strip even with the edge of the roof decking. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails. Overlap the other pieces of eave strip by at least 1” and nail them in place.
What is the difference between drip edge and gutter apron?
The most obvious attribute that distinguishes a gutter apron from a drip edge is the fact that a gutter apron is more of an L-shaped metal rather than a T. A gutter apron also comes in metal strips with aluminum and steel sheets. Like drip edge, a gutter apron may be available in many different colors.
How far should drip edge be from fascia?
Drip edge height: 1 5/8″ Drip edge lip extension: 1/2″ Recommended drainage gap: 1/4″ (approx) spaced off of the fascia board.
Should there be a gap between drip edge and fascia?
The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.
What angle should gutters be hung?
The standard rain gutter slope is half of an inch for every 10 feet. This means that your gutter should be a half-inch lower in height at every 10-foot mark until you reach the downspout.
How far should shingles hang over the drip edge?
Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.
Can you install gutter guards on existing gutters?
Brush Inserts: Like a big pipe cleaner, brush gutter guards can be placed right inside of a gutter by the homeowner. These gutter guards install right on top of your existing gutters and feature a mesh material to keep out all leaves and debris.
Is it hard to install gutter guards?
For the most part, gutter guard installation is not a difficult DIY. If you have general handyman skills, you should be just fine.
Does drip edge go over or under tar paper?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
Does drip edge go around entire roof?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Do you have to detach and reset gutters to install drip edge?
If gutters come in the way of the roof replacement, we’ll first remove the gutters and reinstall them after the new roof installation is complete. There is no additional charge for removing and reinstalling the gutters, but it is essential to have a perfect, leak-proof installation.
Why does water drip from the bottom of my gutters?
It is very simple really. Dirt, pollen, pollutants and petroleum-based run-off from a home’s roof can drip down. They attach to water or dew droplets that form on the lip of your gutters. Eventually these droplets containing the pollutants mentioned above, will drip down your gutter.
Do you nail drip edge to fascia?
You don’t. The drip edge is attached onto the plywood roof decking before any shingles are installed. And assuming that the roof’s bottom edge has a typical fascia trim, that trim should be in place before the drip edge.
Should gutters be flush with fascia?
Should Gutters Be Flush With Fascia Boards? Gutters are installed on the face of the fascia boards. It is recommended to lay down a protective piece of furrier strip rather than leaving them flush. This is because fascia will be exposed to a lot of dark and dampness.
How much fall does a gutter need?
A general rule is that gutters need to slope at least a quarter of an inch per 10 feet to avoid standing water.
How far apart do you put gutter brackets?
Gutter hangers should always be placed at least every three feet for proper support (2 feet in northern climates where snow and ice can add additional weight on the gutters).
Do gutters need a fall?
Domestic eaves gutter, especially when fixed on rafter brackets, should be laid to a fall of not greater than 1:350. Too steep a fall should be avoided, as this leads to an excessive gap between the lowest edge of the roof and the top of the gutter.
Should shingles overhang gutters?
Most shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.
Should starter shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Does fascia go on before shingles?
Fascia and soffit are installed after the roof installation is finished. It is ideal that soffit and fascia materials be installed before you place tiles or any other type of roofing material on the roof.
