Table of Contents
When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
How do you fix Whirlpool Lo FL?
Whirlpool Washer Lo FL Error Make sure the water supply is turned on and you have proper water pressure being supplied to the machine. Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.
How do you clear the error code on a Whirlpool top load washer?
System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
What does lf mean in whirlpool?
Whirlpool Washer LF Error is a water fill error, it stands for Long Fill. It means that the main control has not gotten a signal back from the water pressure sensor which means that water is not filling the tub or not filling the tub fast enough. The control will shut down the cycle and report the LF error.
How do you reset a Whirlpool washing machine?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
What does low FL mean on a Whirlpool washer?
The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.
What does Fl mean on my washing machine?
If Samsung Washer FL Error Code appears on the display panel, it’s likely a door lock malfunction. It indicates the door lock cannot be locked after several attempts.
Why does my Whirlpool washer says low detergent?
Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles.
What does lf mean on a Whirlpool Cabrio?
Long Fill Fault Code Washer Problem LF (F30) Long Fill Ld (F32) Long Drain uL (none) Unbalanced load oL (F70) Overloaded.
How do you fix a Whirlpool washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
What does lf mean?
Summary of Key Points LF Definition: Looking for Type: Abbreviation Guessability: 3: Guessable Typical Users: Adults and Teenagers.
What does lf mean on dryer?
An LF (Lint Filter) Error Code indicates that the HybridCare™ filter has been removed. Place filter into dryer and make sure the handle is properly seated.
How do you clear the LF code on a Maytag washer?
To remove the error display, press Power once. Then press Power again to restart the washer. If pressing Power does not work: Unplug the washer or disconnect the power for one minute.
How do I reset my Whirlpool load and go?
Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What would make a Whirlpool washer not spin?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
How do I manually drain my Whirlpool washer?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer’s discharge hose if the water fails to drain from the washtub.
How do I fix the LF on my Whirlpool washer?
LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
What does Fl mean on a front load washer?
Samsung Front-Load Washer Fault Codes Fault Code Washer Problem LO or FL Door lock error ds Door is not locked dc Unbalanced load Sud (F70) Too many suds.
Where is the water level switch on a Whirlpool washer?
Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.
What is FL error code?
The P2 or FL error code is an indication that the drain pan in the unit is full.
What is E1 f3 Whirlpool washer?
The Whirlpool washer F3E1 error code is a water level system error. The main control is detecting an out of range pressure signal. Check the water level pressure hose from the water level pressure sensor to the air trap. Most the time it’s the pressure switch that has faulted causing this error.
