Table of Contents
Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.
How do you cut a concrete slab by hand?
Use your dominant hand to grip the back handle and push the blade forward and backward. Begin cutting at the edge of the concrete and slowly follow the chalk line. Don’t press the blade into the ground—let the weight of the blade and saw do the work. Remove the blade every 30 to 45 seconds to avoid overheating.
Is concrete hard to cut?
Wet concrete is very difficult to cut, and fully cured concrete can fracture as it’s being cut. So if possible, cut concrete when it’s hard but only half cured. The cut will come out smoother with less dust.
When should I cut my concrete driveway?
Saw cutting can start anywhere from three to six hours after the concrete is poured, depending on the weather conditions. The best way to determine whether the slab is ready is to make trial cuts to check for raveling. Saw cutting should start as soon as the raveling stops during these trial cuts.
Can I use an angle grinder to cut concrete?
Although the various concrete cutting saw is available, an angle grinder is the most convenient tool for small concrete cutting work. A concrete-cutting blade for an angle grinder has a diamond-studded rim with ventilation grooves — a tile-cutting blade uses diamond studs but does not have the grooves.
Can I cut concrete with a Sawzall?
Cutting concrete with a reciprocating saw begins with safety gear. Cutting concrete creates dust and sends sharp shards of material flying toward the tool operator. Because concrete dust can cause respiratory discomfort or damage, reciprocal saw operators must wear face masks or respirators.
Can you cut concrete with a chainsaw?
The hydraulic-powered Lynx LCC31 concrete cutting chainsaw from Stanley Hydraulic Tools will cut concrete (wire or rebar reinforced), brick, block, masonry and stone. It can cut square corners for openings and wall cut-outs, as well as plunge cut into walls and make full-depth cuts at one pass.
Can you cut concrete block with a Sawzall?
Use to cut through brick, mortar, stone, cinder block, and more. Caliastro’s 9-Inch Masonry Reciprocating Sawzall Saw Blade has been specifically designed and tested to cleanly and quickly cut through brick, mortar, stone, cinder block, and more.
How deep can a concrete saw cut?
They can cut through 12 to 14-inches of concrete. It is wise to use a strong power source for cut-off machines to increase their speed. They also become simpler to use and are less noisy. This is even more so if the main focus is on the depth of the cut as opposed to the noise created when in an enclosed environment.
How fast can a concrete saw cut?
Usually, a concrete saw can cut up to 10 feet per minute. The 14-inch blade can easily cut a 5-inch thick concrete.
How soon can you cut concrete after pouring?
For most concrete work, cutting should take place within the first 6 to 18 hours and never beyond 24 hours. Smaller early-entry saws are available, which may allow cutting to begin within a few hours after placement.
How much does it cost to saw cut concrete?
Saw Cut Concrete Cost It costs between $0.60 and $55 per linear foot for this type of work. Concrete contractors near you who perform this job may have a minimum service change that ranges between $50 to $150.
What happens if you don’t cut concrete?
Cutting too early can mark the pavement surface as well as cause joint raveling. Late sawing can result in random concrete cracks. Shallow cracks aren’t sufficient to prevent uncontrolled cracking while deep cuts are excessively labor intensive and undermine the aggregate interlock in the concrete.
How deep can a 16 inch concrete saw cut?
Diamond Blade Cutting Depths Maximum Blade Cutting Depths Concrete Saw Blades 12″ 3 5/8″ 14″ 4 5/8″ 16″ 5 5/8″.
Do you push or pull a concrete saw?
Always let the saw do the work; simply guide its direction, but don’t push it down into the concrete. You only need a quarter-inch cut at this point, but if the saw bites in a bit deeper, that’s fine too. This first guided cut will ensure you keep your cuts straight during the rest of the project.
How many times do you float concrete?
For a really smooth finish, repeat the troweling step two or three times, letting the concrete harden a bit between each pass. At first, hold the trowel almost flat, elevating the leading edge just enough to avoid gouging the surface.
Will a metal grinding wheel on concrete?
Wheels intended for use on masonry are made with a silicon-carbide abrasive. Metal-cutting wheels contain either zirconia or aluminum oxide, depending on their intended use. Silicon-carbide abrasive particles are sharper and harder, and thus continue cutting efficiently on concrete or other masonry surfaces.
What tool do I need to cut concrete?
Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.
How long will a diamond blade last cutting concrete?
According to experts, a low-quality diamond blade can only last around 12 hours of non-stop cutting, while high-quality blades can cut materials up to 120 hours.
Can you cut concrete with a multitool?
Cut Through Concrete with Oscillating Tool Accessories By adding a carbide grit oscillating tool blade, you can use your oscillating multi-tool to cut and shape concrete. You can also use the device for jobs like grout removal.
How much is a Milwaukee Sawzall?
Compare with similar items This item Milwaukee 6519-31 12 Amp Corded 3000 Strokes Per Minute Reciprocating Sawzall w/ Variable Speed Trigger Customer Rating 4.8 out of 5 stars (410) Price $11900 Sold By Globally Sourcing Included Components Unit^Instruction Guide.
