Table of Contents
How do I reset my Bryant electric furnace?
If the furnace doesn’t have a power switch you can turn off, turn off the circuit breaker controlling the furnace, open the blower housing and locate the reset button on the side of the blower motor. Press it in until it clicks and then restore power to the furnace by turning the breaker back on.
What does a reset button look like on a furnace?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
Why won’t My Bryant heater turn on?
Check to make sure that your thermostat is set in the “heat” position. Make sure that the temperature setting on the thermostat is set above (or higher than) the indoor temperature showing on the thermostat. Try turning the fan to “ON” using the fan switch on the thermostat to test for power to furnace.
How do I restart my furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
How do I reset my furnace lockout?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
Do all furnace blower motors have a reset button?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
Where is the reset button?
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
Why is my furnace reset button not working?
Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. Dirty flame sensor rod: Every now and then, the flame sensor rod gets dirty and shuts the furnace off. Make sure you wipe it off regularly. Low fuel: Low fuel is also a common cause of burner failure.
How do you reset a furnace blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
Where is pilot light on Bryant furnace?
Near the bottom of your furnace is a switch that normally says “Pilot,” “On” and “Off.” Find this switch and turn it to the “Off” position.
Why is my furnace not starting?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
Why do I have to reset my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
What is a hard lockout?
Hard Lockout: Caused by a failure internal to the control or by a system fault such as flame out of sequence. A Hard Lockout will result in a no heat condition. To reset from Hard Lockout press and hold the “i” button for 2 seconds.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
How do you relight a furnace pilot light?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
