Table of Contents
A ledger is also a board or beam used to attach a new structure onto the frame of an existing wall. Any project that requires adding to the side of a house or other structure, will include a ledger.
What is a ledger on a house?
Ledger Board Definition A ledger board is a horizontal lumber beam attached to an existing wall and used to tie in construction elements such as porch roofs and decks. A deck ledger is installed as part of the deck frame construction. The frame is then attached at either end, with the deck joists butting up to it.
What is a ledger board?
Definition of ledger board 1 : a horizontal board forming the top rail of a simple fence or the handrail of a balustrade. 2 : a flooring board in scaffolding.
What is a ledger in roofing?
The ledger, typically a 2 by 6, is usually designed to hold one end of the patio-roof rafters. Locating and mounting the ledger is normally a fairly easy process; the ledger should be attached before the foundation is built for a deck, patio roof posts, and other structure.
What is a ledger plate used for?
noun Carpentry. a strip of wood laid flat across the tops of studding as a support for joists.
Is a ledger board structural?
Attached decks, or ledger decks, are fastened to a building’s wall using a piece of naturally decay-resistant lumber, pressure-treated dimensional lumber, or engineered lumber known as a ledger board; often simply referred to as a “ledger.” It’s usually bolted or screwed to the structural framing inside the adjoining Sep 7, 2021.
When would you use a ledger board?
The ledger is made of the same material as the rest of the framing—usually pressure-treated lumber. Some builders install the ledger first, before they lay out for the footings and dig the post holes. They then use the ledger as the basic point of reference for determining footings, posts and all the framing.
Can you attach a ledger board to studs?
Mike Guertin (on Instagram @mike_guertin), a builder and remodeler in East Greenwich, R.I., and a presenter at JLC Live, responds: Yes, it’s technically possible to fasten a deck ledger to the narrow faces of 2-by studs rather than to a solid rim joist.
How do you attach a ledger board to concrete?
Use a wood bit to drill ½” pilot holes through the ledger board. Next, use a concrete bit to drill into the concrete wall. Install two bolts at the end of each ledger board. Hammer the sleeve anchor through the ledger board into the concrete wall.
What are ledgers in scaffolding?
Ledgers are 48mm diameter tubes with a cast wedge fixing device at each end. They are positioned horizontally between two vertical scaffold standards to give the length of the scaffold bay, at platform level. They may also be fitted as a handrail.
Do I need a ledger board?
Yes, the deck needs to be tied to the house. You will want to install a ledge board that’s lag bolted to the structure of the house. That means through the brick/sheathing and into the rim joist. And, of course, you should use the appropriate metal hanger to tie the joists of the deck to the ledger board.
What is a ledger balance?
A ledger balance is a balance in an account at the beginning of each day, also known as the current balance. It includes all deposits or transactions that were posted from the previous night, whether any money has been collected or disbursed.
How do you attach a ledger board to a brick house?
Onto Brick Veneer Mark anchor locations on your ledger and drill through the board with a ½” bit. Position the ledger against the wall and mark the anchor positions through the hole onto the wall. Drill through the brick veneer with a ½ inch masonry bit in a hammer drill, until you reach the wood frame behind.
Can you put ledger board over siding?
Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Wood or concrete siding will have to be cut away using a circular saw. Set the blade depth so you won’t cut into the house sheathing below the siding.
Does a ledger board need flashing?
How to Flash a Deck Ledger Board. If you cut out your siding to install a ledger board, careful steps must be taken to ensure that moisture cannot reach your house. Infiltrating rainwater can travel downward, sideways and even upward, so special flashings must be used.
Is a ledger a beam?
A ledger is also a board or beam used to attach a new structure onto the frame of an existing wall.
Can a ledger board be two pieces?
The ledger board doesn’t have to be one continuous board. It can be a series of broken sections if it is solidly attached. This will require extra bolts and installing a 2x nailer across the top of the vent to secure the decking along the house wall.
How many lag bolts for a ledger board?
Since 2009, every edition of the IRC (including the anticipated 2021 edition) requires the deck ledger to be connected to the house floor band joist with ½” bolts or lag screws as shown in Table 507.9.
How does a ledger board support joists?
A ledger board — a flat piece of timber anchored to the frame that evenly spreads the load of the joists it supports — is used for the installation of hangers. Joist hangers help to keep joists anchored over time and absorb the forces of the structure above.
