Table of Contents
How do I unlock my Marquis spa control panel?
Panel Lock Press TEMP+ or TEMP- pad followed by QUIET SOAK pad to lock. Then press TEMP+ or TEMP- pad followed by QUIET SOAK pad to unlock.
How do you unlock Catalina Spas in a hot tub?
To unlock the panel, press “Time” “Jets 1” then “Cool.” Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm” within 3 seconds to activate the lock. The TL indicator light will light when the set temperature is locked.
How do you reset a Hydropool hot tub?
Remove the spa cover and allow water to cool. Once the heater has cooled, reset by pushing any button. If the hot tub does not reset, shut off power to the spa and call your supplier for a service.
What does F4 mean on hot tub?
8 hours daily CODE ERROR CODE DESCRIPTION F4 8 hours daily filtration; system message, not an error F6 12 hours daily filtration; system message, not an error F Fahrenheit, used to indicate panel is in Fahrenheit mode; system message, not an error FB-ER Fiber optic error; accent lighting.
Why is my Vita Spa not heating?
If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.
How do you turn off a vita hot tub?
To toggle the pumps on and off, simply press the jets you would like turned off. That will switch off the therapy pump you indicated. Note: The circulation pump cannot be toggled on and off on the touch screen as it is designed to run at all times to keep the hot tub running effectively.
How do I reset my hot springs control panel?
Move the remote closer to the spa. Press the Jets button on the dock unit; if it’s necessary to reset the panel, press and hold the touchscreen in any blank area until it turns black.
Do hot tubs have a reset button?
A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
What does Dr code mean on hot tub?
Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube, says Niagara Hot Tubs. If the water is low, add water to the proper level and try restarting the pump and heater.
How does Catalina Spa work?
How to Operate a Catalina Spa Open the gate’s valves. Install the filter cartridge. Fill the spa at least halfway up the throat skimmer. Purge air from the system. Turn the pump on high. Cycle through all the functions for the pumps. Test the water with the test kit. Set the water temperature.
Why wont my hot tub jets work?
Jets Are Not Working Properly When jets start failing, the most likely case is that your hot tub pump is not working correctly. This releases air from the line and purge system, allowing more water to stream through the jets. Clogged filters or water intakes can also cause jet issues. Clean them to enhance water flow.
What does Flo mean on hydropool?
Q: What does error code ‘FLO’ mean? A: Your spa has recognised water flow past the heather has stopped or is insufficient.
How do you drain a 2020 Hydropool hot tub?
Draining Your Hydropool Hot Tub Start by putting the tub on standby. Take the tub off standby. Turn off the air controls to the tub, add Drain Prep, put the jets on and leave the tub for a minimum of 6 hours. After 6 hours has elapsed, turn the temperature down. Activate the standby mode.
What does ECN mean on hot tub?
Economy mode Error Code Meaning Ecn The hot tub is in Economy mode Slp The hot tub is in Sleep mode. Sby The hot tub is in Standby mode. 40 Set time of day.
What does HH mean on a hot tub?
HH – Overheating Your spa has detected an excessively high temperature at the sensor in the heater chamber. The hot tub is shutting down to protect users from dangerously hot water.
How do you fix the error code on a hot tub?
This error message is similar to the FLO error message. Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.
How do I reset my Cleverspa heater?
Reset the hot tub by pressing the ‘Off/Test’ button on the RCD plug. a. Wait 10 seconds then press ‘On/Reset’ to turn it back on again.
Why is my Cleverspa not heating up?
It may be that your filter is dirty. A dirty filter will not efficiently allow water to be drawn through the internal heater, where it would be heated and pumped back into the hot tub. Check your filter is clean, if you are unsure watch our video.
