QA

Which Side Of Hardie Board Goes Up

Which side goes up, smooth or rough? Either is acceptable, but we recommend that the smooth side with the nailing pattern of every 8″ on center go up.

Does it matter which side of cement board faces out?

No, it doesn’t matter. Regardless of which side faces out during installation, you can expect the same great performance that has made USG Durock® Brand Cement Board the preferred choice of professionals and do-it-yourselfers for decades.

Can Hardie board be installed backwards?

You can’t mount it backwards; the back side of it isn’t smooth. I wish that so-called wood grain products were more subtle- the grain is usually way over done.

How do you layout cement board?

#2 A cement backer board layout should be staggered. It’s kind of like building a wall of Lego’s. If you set each one directly on top of each other it is unstable. You create a stronger, more stable floor by staggering the backer board. Likewise, four corners of cement board should never meet at one point.

Do you have to pre drill Hardie board?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

How do you mount Hardie board?

Drill pilot holes, at each mark, one-quarter to one-half inch deep, to make it easier to insert screws and prevent cracking the siding. Align the bracket holes with the pilot holes in the siding. Insert the screws and tighten securely using a drill with screwdriver bit attached. Hang the basket on the bracket.

Can you tile straight onto backer board?

As a building material, interior fibre cement tile backer board products are especially suited as a tiling base for tiling wet areas such as bathrooms, kitchens and showers as it is resistant to permanent water damage and does not need to be treated before tiling.

Can I just screw down cement board?

Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on​ the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.

Do you need to put thinset under Hardie board?

However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.

Do you caulk Hardie board siding?

James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).

What do you do with a gap between tub and cement board?

Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub.

Do you have to tape seams on Hardibacker?

For tile backer boards such as Durock, Wonderboard, Hardiebacker, Permabase, and others the seams between the board need to be treated with 2-inch alkali-resistant mesh tape.

Do you nail or screw Hardie board?

What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.

Is it OK to screw into Hardie board siding?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.

Do you have to put plywood behind Hardie board?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches.

Should I wet Hardibacker before tiling?

A. To be more precise, I’ve installed lots of concrete backer board for years, all with good results. The concrete is unaffected by any water that manages to get behind the ceramic tile. If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to.

Can you tile on Hardie board?

HardieBacker® cement board may be installed under or over Vinyl Composition Tile (VCT) and other resilient flooring. For best results, remove existing floor covering, especially if it is in poor condition.

What do you put on seams of cement board?

Use special mesh tape on seams Cover all of the corners, joints and seams, including the joint where drywall and cement board meet, with the fiberglass mesh tape.

What do you cut cement board with?

First, you’ll want to choose a scoring tool. A carbide-tipped scoring knife is recommended, but you can also use a utility knife or shears. Never use a high-speed grinder to cut cement board indoors, since this can create a dust hazard.

How long before you can walk on cement board?

However, after you mount the backer board to the floor you simply have to seal the seams with mortar and wait until the mortar dries. This is normally 12 hours but may be up to 24 hours in some cases.

Do you caulk Hardie panel?

Panels may be installed first with caulk applied in the joints after installation; or as an option, after the first panel is installed, apply a bead of caulk along the panel edge.

Can Hardie panel be installed horizontally?

HardiePlank® is more resistant to moisture damage than wood siding, so if you choose horizontal siding, it’s a great option.