Table of Contents
When the green light is flashing fast, it means you have got a working blower system and your furnace is providing heat to the home. If the green light is flashing slowly, it means the furnace is on but there is no request for heat. A continuous light likely means that the IFC circuit board needs replacing.
Should my furnace light be blinking?
When your furnace light flashes, that’s just another way it’s trying to communicate with you that there is a problem. When you see a flashing light, your furnace is sending you an error code. Check your circuit breaker box to see if you tripped the breaker for the furnace.
Why is the red and green light flashing on my furnace?
Look inside your furnace control panel. You should be able to see a blinking green light. If the light is not blinking green, but blinking red or not blinking at all, make the call. It usually means that you have an issue with your blower or some other component part has failed.
How do you read a furnace error code?
Although furnace error codes differ between brands, all the most popular furnace brands use a system of blinking lights to communicate error codes. To read a furnace error code, locate the LED light and note its blinking pattern. Be sure to count how many times the light flashes and to note how quickly it’s blinking.
How do I reset my furnace?
How to Reset an Electric Furnace First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
Why is my furnace not blowing hot air?
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not ‘on’. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
Why is my furnace blinking 3 times?
What it means: Have you ever looked at your furnace and thought what do 3 flashes on American Standard furnace mean? This error occurs when the combustion air pressure switch that monitors the flow of air through the vent system fails to close while the induced draft motor is operating.
What does it mean when my furnace light blinks 4 times?
Why is my furnace light blinking 4 times? Four red flashes indicate that a 24-volt fuse or the high-limit switch is open. Possible causes include an improperly sized ducting system, a dirty air filter, a faulty blower motor, an open fuse on the control board or restricted circulating airflow.
Why is my furnace not starting?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
What does 6 blinks on a furnace mean?
When the light is blinking six times rapidly, this means the power volt polarity has gotten switched.
Why is yellow light flashing on my furnace?
What it means: If you’re wondering, “What does the yellow light on my Carrier furnace mean?” it signifies that the furnace is stuck in high-fire mode. The high-fire mode should only operate for short periods of time to heat a very cold house faster.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
Where is the reset button?
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
Do all furnace blower motors have a reset button?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
How do you tell if your furnace is venting properly?
How Do I Know If My Furnace Isn’t Venting Properly? Gas furnace fumes are moist, so if you notice “sweat” on your windows, this is a sign that your furnace isn’t venting correctly. When your furnace comes on in the morning, if it is venting into your house rather than outdoors, moisture will condense on the cold glass.
Why is my furnace blowing cold air sometimes?
There are several different reasons your furnace may be blowing cold air. A furnace that blows cold air could be a result of an improper thermostat setting, a dirty air filter, a faulty fan limit switch, or something else entirely.
