Table of Contents
Does decking overlap fascia?
Safety – Having a picture-framed deck adds safety to your deck as well. Yes, it’s true. Perimeter picture-frame deck boards overlap the outside rim joist and any decorative fascia board.
What do you use for fascia on a deck?
If you choose to add fascia, any kind of pressure-treated or otherwise rot-resistant lumber can be used. However, if you’ve opted for synthetic decking in one of the many colors available, you’ll want to consider using a complementary PVC fascia. PVC fascia typically comes in 1/2-in. x 11-3/4-in.
Should decking be flush with fascia?
Here’s where you’ll run into the question, what is better, deck board overhang or flush? Building practices say deck board overhang is better than flush. The overhang helps your deck look stunning and last longer. Both the stair nosing and deck boards overhang to protect the substructure.
What is a deck fascia board?
A DECK FASCIA BOARD is the board that runs around the perimeter of the deck for a seamless look. Fascia covers the wood perimeter joist of the deck frame and is sometimes called “rim joist cover.”.
Should deck boards hang over?
The edge of decking should never overhang more than one-third of the decking material. For your standard 5.5” decking, that is 1 ¾” overhang.
How do you finish decking edges?
Conclusion. How to finish the edge of a composite decking is simple if you use picture framing to cover the board edges. You can also paint the edges, glue a veneer cap to the ends, attach a raised fascia board or add a composite corner trim to create a consistent look.
How far can a deck board overhang?
The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
What is the best material for fascia boards?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
How thick should fascia boards be?
Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction.
Can I use composite deck boards for fascia?
Fascia is the vertical band of material that borders below the deck surface. The main purpose of fascia on a composite deck is to conceal the outer rim joist and serve as a transition piece from deck to skirting. Another option is to use two deck boards as fascia.
What can I put around my deck instead of lattice?
If you don’t like the look of the lattice as a cover for under the porch, here are a few alternatives: Vertical wooden planks. Horizontal wooden planks. Wooden planks with a pattern or design. Rock porch skirting. Brick or stone. Alternative pattern vinyl lattice. Enclose the space.
What is the board behind the fascia called?
Soffit is the layer of wood, vinyl or aluminum that extends from the bottom of the fascia to the top piece of your wall board. Together, they protect the rafters from weather, moisture, and allow air to flow through soffits and vents.
How hard is it to install fascia board?
Fascia boards are found around the edges of your roof and usually support your home’s rain gutter system. Luckily, replacing a fascia board is as easy as taking out the old board and fitting a new one in its place. Once you’ve installed a new board, all you need to do is seal the seams and paint it to match your home.
Can you curve decking?
Composite decking is flexible enough to be bent across curved sections of the deck. If the decking is hot it will be even easier to bend into the desired shapes. Fascia board is flexible and can be installed over the rim board to clean up the edges.
How do you build curved stairs for a deck?
The curvature of the stairway complicates framing, though once the bracing for the stringers is added, it is much like standard stair framing. Add bracing. Cut a trial stringer. Lay out the pad. Install the stringers. Add the top and bottom risers. Install any lights. Complete the tread installation.
How do you curve timber decking?
The easiest way to frame a curve is to run joists long. Then hook a marker to the end of a wire, chain or non-stretchy cord and swing an arc from the center of the circle. Cut the joists at the marks and you’re on your way to a curved deck.
How do you hide the edges of a composite deck?
The question is, how do you hide the ends of composite decking? There are several ways to go about it. Some of your options include picture framing, installing fascia boards, coating the ends with paint, using end caps and plugs, or edging your ground-level deck with stone.
