Table of Contents
At initial start up or after a thorough cleaning, the filter will need to be pre-coated with DE. The filter label will state the amount of DE required. Start the pump and once the pump is fully primed, measure the DE using a DE scoop, part # EC10SC. Slowly add the DE into the skimmer.
What happens if you don’t add DE to pool filter?
If you do not add enough DE to your filter, then the grids are not totally coated with DE and the dirt that goes into your filter will attach itself right to the fabric on the grids and will not backwash off. This will cause your filter to short cycle (go very short times between backwashing).
How much diatomaceous earth do I put in my pool filter?
Most DE filters include a recommendation for the total amount of DE powder on a fresh filter. However, if you can’t find a suggestion from the manufacturer, you can use a simple rule of thumb: For a full clean or new filter, add one pound of DE powder for every 10 square feet of the filter.
How often should I add DE to my sand filter?
DE particles are microscopic and have many sharp edges, trapping fine dirt particles that would otherwise be able to get through the sand. Small amounts of DE can be added to a sand filter after each backwash to improve the filtering.
How often should I backwash My DE filter?
Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. “When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use.
Do I add DE Every time I backwash?
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
Can you run a DE filter without DE powder?
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
Can you put too much DE in a pool filter?
AVOID ADDING TOO MUCH DE POWDER – One of the most common causes for getting DE Powder in your pool is adding too much DE powder. The grids will have retained some of the DE Power after the backwash, and if you add too much, it may end up in the pool.
What happens if you add too much DE to pool filter?
Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
Can you swim after adding DE to pool?
How Long Do I Have To Wait To Swim After Adding Pool Chemicals? It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool.
Should I use DE in a sand filter?
DE Powder. Diatomaceous Earth, used in D.E. pool filters, can also be used in sand filters and cartridge filters to trap particles down to 3 microns in size. Use 1-3 cups depending on your filter size, by pouring it into the skimmer after backwashing, and it forms a layer on top of and down into your sand bed.
Should you add DE to a sand filter?
Adding DE To Your Sand Filter That is what makes DE filters top of the line when comparing the three different filter types. However, DE powder can also be used with sand filters to improve their filtering quality. You can add small amounts of DE powder to your filter after each backwash to improve your filterability.
How often do you change DE powder?
You should clean your DE filter at least once every month or whenever you’re pounds per square inch is 8 to 10 pounds above the normal starting pressure. Cleaning your DE Filter involves three basic steps: Backwashing, Cleaning the manifold and grid and adding new DE. The first step in cleaning your DE is to backwash.
How many pounds is a DE scoop?
A DE Scoop is specially designed to measure DE powder and 1 scoop is equal to 1/2 lb. of DE powder. To determine how many scoops or coffee cans of DE your filter requires take your filter square footage and divide by 5 (this would be after a full cleaning).
Why does my DE filter pressure keep rising?
If your filter pressure is higher than normal, this usually indicates a dirty pool filter. We generally recommend backwashing your filter (or cleaning your cartridges) when the pressure rises 8-10 PSI above the clean start-up pressure. Either scenario will cause the pressure to rise to very high levels.
How much diatomaceous earth do I need to backwash?
If you are replacing DE Powder after a backwash, you will not need to add the full amount – generally around 80%. The grids will have retained some of the DE Power after the backwash, and if you add too much, it may end up in the pool. The best way to assess how much DE Power to add is to monitor the pressure gauge.
Why is my pool filter blowing out DE?
Common D.E. Filter Problems: DE Blow-Back: If DE powder is coming into the pool, you may have torn filter grid fabric. Or, you could have a cracked top manifold, or missing air bleeder. The standpipe o-ring could be missing, or the filter valve could be allowing some DE powder to bypass the filter as you add it new.
How long do DE filter grids last?
Grids usually last a long time, up to about 10 years unless they are subjected to extreme conditions for extended periods.
