QA

Where To Buy Bathtub Plug

Are bathtub plugs standard size?

According to Bonnets Stems and Accessories, Inc., a standard modern bathtub drain is 1 1/2 inches in diameter – the width straight across the middle. Rough-in plumbing should be calculated for a 1 1/2-inch pipe.

What can I use instead of bathtub plug?

Ways to Block a Bathtub Drain Use a Small Plastic Cup. Use Plumber’s Putty. Find a Jar Lid of the Same Size With the Drain Hole. Use a Toilet Plunger. Plug the Drain With a Washcloth Stuffed Inside a Plastic Bag. Tape the Drain Hole. Use a Marine Drain Twist Plug.

What is the plug in a tub called?

Also known as a foot plug, a push-pull drain stopper opens and closes just as its name describes. You pull up on its small knob to open the drain and push down to close it again. This simple drain stopper is easy to remove and install and has a long lifespan.

What size are bathtub plugs?

Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep. They are this size because they must fit the opening of the P-trap — also 1 1/2 inches wide — which is a special pipe that has a sharp bend in it.

How do I know what size bath plug I need?

To determine the right size of plug, you need to measure the diameter of the drain mesh or the underside of your current plug. Then you’ll be able to shop for the style of sink plug you want and be able to choose the right size the first time.

Are all bathtub drains in the same spot?

All bathtubs drain in basically the same way, with a drain assembly located on the bottom of the tub linked to an overflow that may or may not have a toggle switch. When the plunger or stopper is opened, water drains out of the bathtub, through the drain assembly, down a tailpiece and into the trap.

How do you make a homemade bath plug?

Create a makeshift drain plug using a washcloth or small sponge inserted into a small plastic bag. Twist a wet washcloth tightly or wet a sponge that has been rolled to fit the drain. Place the cloth or sponge inside a plastic sandwich bag.

Why does my tub not hold water?

If your bathtub doesn’t hold water, the culprit might be a faulty bathtub drain stopper. It also drains the tub when not in use. In most cases, an issue with the bathtub drain stopper is usually because it has disconnected from the spring or plug that connects it to the linkage.

Are tub stoppers universal?

Although they all serve the same purpose—to keep water in the bathtub when desired and allow the tub to be emptied again—there are several different styles of bathtub drain stoppers. The most common types of bathtub drain stoppers are lift-and-turn, push-and-pull, pop-up, toe-touch, flip-it, and trip lever.

Do tub drains come in different sizes?

Shower or tub drains have different drain connection sizes to accommodate the pipe sizes of your plumbing drain system. For example, your bathroom might have a 2” drain and 3” drainage pipe. Be sure you have all of the essential supplies on hand if you intend on replacing drains.

Are tub drain locations standard?

The position of the tub drain will vary, depending on the size and design of the tub, and you’ll need to cut an access hole in the floor at the drain end of the tub to allow for positioning and installing the drain line. This hole should be 9 inches wide and extend at least 12 inches from the wall.

How do you measure for a new plug?

You can measure the old plug across its top diameter (in imperial). You can try and measure the plug hole; this should be done across the top diameter, but the rim may be bevelled, which can confuse matters.

Can you replace a pop up plug with a normal plug?

Yes, but a waste that’s designed for a plug has a grille set down 10mm or so for the plug to sit on. But if you can find a suitable plug then happy days. I replaced the pop up plug with a standard 1.5″ plug and chain – leaving the horizontal rod with the threaded can in to stop sink waste water coming out.

How do you measure a bathtub stopper?

Measure from the piping section where it branches out toward the drain over to the drain hole and write that horizontal distance measurement down. That will give you the length and width that is needed for your drain. Your local hardware or home improvement store should carry a bathtub drain that fits your needs.

Where is my tub drain located?

The easiest way to figure out which kind of tub you’ll need is to stand in front of your shower as if you are going to go into it. If the drain is to your right you have a right handed tub, and if the drain is on your left you have a left handed tub.