Table of Contents
Can I replace a pilot light with electronic ignition?
When the pilot light of a gas-fired boiler or furnace burns constantly, energy is wasted. This type of pilot light can be replaced with an automatic electric ignition that ignites the pilot only when the thermostat calls for the furnace to be fired.
Can I convert my gas fireplace to electronic ignition?
Some gas fireplaces can be upgraded with electronic ignition systems to boost fuel conservation and efficiency. The savings you realize from the use of an electronic system will far outweigh the small cost of the change. This applies whether you retrofit your old fireplace or completely change the system.
How do I light the pilot light on my electronic ignition?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.
What is the advantage of electric spark ignition over pilot light ignition?
The automatic pilotless ignition (also called automatic electric or automatic electronic ignition) eliminates the need to light the burners. It also saves money by using less gas than a standing pilot range. Because this system has no standing pilot light, no gas is being used unless it is needed.
Does a furnace with electronic ignition have a pilot light?
An electronic ignition is a device that replaces conventional pilot lights in almost all newly-manufactured furnaces. Like a conventional pilot light, an intermittent pilot light still uses a small, gas-powered flame to ignite the furnace’s burners.
Can gas water heater be converted to electric?
Switching from gas to electric While not as common, it is possible to switch from a gas water heater to an electric one. A professional will also need to turn off the gas line for the old gas water heater. Overall though, the upfront costs of installing an electric water heater are usually lower than gas.
Can I get a remote for my gas fire?
Gas Fireplaces Are Compatible with Specific Remote Controls Fireplace remote controls provide plenty of added convenience for gas fireplaces; however, they do require compatibility with certain remote controls. With all of the options available today, it can be confusing as to what type may be best for your needs.
Can I add a remote to my gas logs?
Yes, you can add a remote to your gas log set after it’s been installed and the log set is already equipped with a millivolt valve. You may even be able to completely convert your gas log set to a remote control system with variable flame and thermostatic controls.
Can you manually light a gas furnace with electronic ignition?
If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.
Can you manually light a gas water heater with electronic pilot?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.
Are pilot lights automatic?
One component that varies from system to system is the type of pilot light. Most newer models use an Electronic Ignition System (or automatic) while older models likely have a standing pilot light.
What is the difference between millivolt and IPI?
The difference between the IPI compared to the Milivolt system is that a Milivolt has a pilot light that stays on 24/7. The IPI system does not use a pilot light and instead relies on an electronic ignition switch to light the pilot after flipping on the wall switch or using the remote.
What are the two types of pilot lights?
There are two types of electronic ignition, intermittent pilot and hot surface ignition. An intermittent pilot system generates a high voltage electrical spark whenever the thermostat calls for heat. This spark ignites a gas pilot, which then works just like the standing pilot light did.
How do I reset my electronic ignition furnace?
To reset the ignition control module on an electronic-ignition furnace, turn down the thermostat or turn off the power switch. Listen for the sound of the spark or watch for the hot surface ignitor to glow. Next, make sure the furnace’s flame sensor is clean.
How do you reset the pilot light on a furnace?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
How much does it cost to convert a gas hot water heater to electric?
Electrical wiring fees can cost between $500 and $1,500 on average. If you’re interested in converting from a gas water heater to an electric heater, it can be an additional $200 to $500 or more. Electric heaters require their own dedicated circuit and cannot be put on an existing line.
How do I start a gas water heater without electricity?
It’s very easy and safe. Turn on your gas and use an electric lighter to light the pilot. This heat source will allow your water to be heated the entire time. You will never have to wait for warm or hot water again.
