Table of Contents
Try backwashing and rinsing your media filter to ease the path for the water. If this doesn’t work, turn the pump off and set your filter to recirculate. If you now have normal flow, try backwashing again, if it still doesn’t work you may be due for a media change.
How do I get water to flow through my pool pump?
If your pump looks like there is no water in it, turn it off and unscrew the pump lid without losing the o ring. Fill up a bucket with pool water and pour it into the pump, this is called priming. Once the water level reaches the top, replace the pump lid with the o ring and turn your pump back on.
What does no flow mean on a pool?
The “No Flow” light indicates that the flow switch is not detecting sufficient water passing through. Check the following: cleaning the cell or the filter (see how to backwash a DE Filter or Clean a Cartridge Filter).
Why does my pool heat pump say no flow?
Verify filter and skimmers are clean. Check water level in pool. Verify circulating pump is on and that there are no water flow restrictions to the heat pump. Make sure all necessary valves are open or in the proper positions to allow proper water flow to the heat pump.
Why my pool pump has no pressure?
When the pressure is lower than normal, this usually indicates a flow problem, and usually something is blocking or restricting water flow into the pool pump. It’s never a problem after the pool pump, because after the impeller, the pool water is under pressure, and obstructions result in higher than normal pressure.
How do I know if my pool filter is clogged?
The easiest way to know if your pool’s filter is working properly is to check its pressure gauge on a daily basis. If the filter becomes clogged, it can suffer serious damage, which means your pool will not be cleaned and sanitized properly.
Can you snake a pool line?
Also, do not try using a plumber’s “snake.” A snake typically doesn’t work on pool pipes because pools use 90-degree elbows and house plumbing uses 90-degree “sweeps,” which allow the snake to round the corners. Also, a sewer-line snake should not be used on a pool for sanitary reasons.
What does Flo mean on pool heater?
The FLO code is indicating that the filter pump has stopped the flow of water to your heat pump. The heat pump cannot heat without water flow so it will turn itself off until the filter pump timer turns back on giving the heat pump the water flow it needs.
Does a pool heater restrict flow?
Many pools have an expensive heater in their water flow. Water circulates through the heater core all the time the pump is running, whether the heater is on or off. If the heater springs a leak, you have to shutdown the pump, which stop waters circulation, filtering and chlorinating your pool.
Why is one of my pool jets not working?
The most common reason for weak jets is an air leak. An air leak would come from the suction side of the system. This would be the area between the skimmer and the pump. One way to determine if you have an air leak is by looking for air bubbles coming out of the return jets.
How do you fix a pool Jet?
Mix the two parts of the epoxy, the resin and hardener, together. Use equal parts of each — about a marble-sized amount of each does the trick for most jet leaks. Knead them together like a rubbery clay, using a few dabs of pool water if needed. The putty should take on a doughy, pliable consistency.
How do I know if my flow switch is bad?
”No Flow” light coming on probably means the cell’s flow switch has gone bad. Verify that the pump is running first (water is actually flowing through the line). If “No Flow” stays on the flow switch needs replacing. ”Flow” LED turning from green to red means water flow through the system has been disrupted.
How do you bypass a flow switch?
Broken Flow Switch Use another short piece of wire to connect the two wires you just pulled off that connect the spa to the main control panel. This action bypasses the flow switch and completes the electrical circuit back to the main control panel.
How long does a pool flow switch last?
With proper care, a cell will last about five years. Eventually, though, it will need to be replaced.
Why is skimmer suction low?
After backwashing or cleaning the filter (and pump basket), you have what is known as the clean, or start-up pressure on the gauge. When pressure rises 5-10 lbs on the gauge, as a result of the filter loading up with dirt, flow rates will reduce, and this will result in lower suction at the skimmer.
Why is pool filter not working?
If the water is not moving through the filter at a normal rate, there is most likely a clog or obstruction before the pool filter. It could be a clogged pump basket, impeller, pipe, or skimmer basket. In some cases, the pump may have an air leak and is drawing in more air than water.
Can pool filters get clogged?
TroubleFreePool.com explained that when your filter is brand new, water can easily pass through the system without issue. However, as the filter continues to do its job, debris can accumulate over time and slowly clog the system. If neglected, a clogged filter can lead to reduced water flow and cloudy water.
