Table of Contents
What oil Can you use in place of bar and chain oil?
Canola Oil It’s one of the most used bar oil substitutes, is usually on hand in most households, and is relatively cheap wherever you live. In some locations, it is up to 50% cheaper than real chain oil. Canola oil is slightly thinner than regular chain and bar oil.
What can I use if I don’t have bar and chain oil?
6 Chainsaw Bar & Chain Oil Alternatives Vegetable Oil. Vegetable oil is one of the safest alternatives available to oil your chainsaw. Canola Oil. Similar to vegetable oil, canola oil is another super-safe alternative. Motor Oil. Hydraulic Fluid (Diluted) Drained Motor Oil (Diluted) Drained Hydraulic Fluids (Diluted).
Can you use 10w30 for bar and chain oil?
Normally, you would need to use bar and chain oil to lubricate your chainsaw because this type of oil was specifically formulated to be used on chainsaws. As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil.
Can you use engine oil as bar oil?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it’s not sticky enough to stay on the bar and chain. So, when you’re using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
What oil is best for chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
Can you use 2 stroke oil as bar oil?
No, it is not. 2-cycle oil is a gasoline additive that provives lubrication to the internal engine parts since the engine has no oil internally. Bar and chain oil is a much heavier viscosity intended for lubrication of the bar and chain specifically.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated. Electric chain saws use the same type of lubrication for the bar and chain as gas-powered chain saws.
What weight is bar and chain oil for chainsaw?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use transmission fluid for chainsaw bar?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use 5w30 for chainsaw bar?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
Can you use old motor oil for chainsaw bar?
Yes you can in a pinch, but motor oil is much thinner than bar oil and you will use it very fast. Chainsaw bar oil is thick and sticky and is designed to be used on bars and chains.
Is bar and chain oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
How do I lubricate my chainsaw?
The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir. Using a small funnel, slowly pour the bar and chain oil into the reservoir, taking care not to overfill.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Can you use wd40 on a chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
Can I use motor oil for chainsaw?
Motor Oil. Chain saw bar and chain oil isn’t rated by SAE like traditional automobile motor oil. If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
