Table of Contents
How do I make my shower head higher?
The easiest and most affordable way to raise the height of your shower head is with an adjustable shower arm. This type of shower arm attaches to your existing shower arm pipe, acting as an extension, and then you can attach your existing shower head.
How do you raise a shower valve?
What is this? Hold the mixing valve into place where you want it and mark the nearest stud at the vertical center of the valve. Measure the vertical distance from the old mixing valve to the new position; you will need to cut two pipes this length to raise the cold and hot water pipes to this height.
How do I move my shower head plumbing?
How to Move a Plumbing Fixture in the Shower Turn off the watter supply to the house, then open all faucets to drain as much water out of the system as possible. Remove the tubing straps securing the shower valve to the framing. Cut the all the pipes coming to and from the existing shower valve.
How do I adjust my shower head without changing plumbing?
How to Raise a Shower Head Without Moving the Plumbing in a Wall Turn the shower head counterclockwise and unscrew it from the shower neck. Wrap a hand towel around the shower neck, then use the adjustable pliers to grip it and turn it counterclockwise.
How high should a shower head be above your head?
What Is the Standard Shower Head Height? Let’s tackle the most important question right away by pinpointing the standard height for a shower head. According to Hunker, the industry standard for how high a shower head should be is 80 inches.
Why were shower heads so low?
So the hotels ought to set the standard shower height of 9 feet. Besides, some silly people would possibly angle the shower head so it sprays over the curtain bar or shower door, and wet the complete bathroom. Low hotel shower heads might cut down on spray accidents.
How deep is a shower valve?
These are shown in the drawings. The depth measurement is critical. wall position, including tile (2-1/16″ [52mm]). The center line of the supply and discharge piping should be a maximum of 2-3/16″ (56mm) and a minimum of 1-7/16″ (37mm) behind the finished wall surface.
What kind of shower valve do I have?
If you want to know how to identify the shower valve manufacturer, check behind the shower handle at the center of the trim plate for the manufacturer’s symbol or brand name. You will see one of the following shower faucet logos: K: the manufacturer is Kohler. M: the manufacturer is Moen.
How hard is it to relocate a shower head?
A. It’s neither difficult nor expensive if you are tearing out the existing shower walls, which normally is advisable when you are remodeling your bathroom. All you need to do is run the hot and cold water supply lines to the end of the shower opposite the shower head.
Can you relocate a shower?
When moving a shower, you’ll also need to install the shower head in the new location. You can either have your current shower head reinstalled or choose a brand new one. This also requires plumbing expertise, especially if you decided to attach the shower head to newly installed pipes.
How much does it cost to relocate a shower head?
Professional Installation. If you opt for professional installation, the cost for showerhead removal and replacement is roughly around $50 to $100 for labor fees, not including the price of the actual showerhead.
What do I do if my shower head is too high?
If your shower head is too tall, get an extendable shower arm. You don’t have to do any in-the-wall plumbing to lower your shower head. An extendable shower arm allows you to lower your shower head to the height you desire. Visit a bed and bath retailer to find an extension that’s right for you.
How do I fix my adjustable shower head?
Step 1: Unscrew shower arm from pipe with strap wrenches. If you use different wrench, tape pipe to avoid scratching it. Step 2: Clean arm threads and coat them with plumbers’ joint compound or wrap plumbers’ joint tape around them. Step 3: Screw head back on and hand-tighten it.
How far should the shower head be from the wall?
Typically, a wall-mounted or fixed shower head should be about 3 to 4 inches from the wall. If you angle the shower arm at 100 or 120 degrees, you’d have enough space to move around your bathing enclosure without bumping against the wall.
How high should shower taps be?
Shower Valve Height A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units. For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. Install faucets at the same height as the valve, equidistant from the valve.
What is the minimum height for a shower?
A shower or tub equipped with a showerhead shall have a minimum ceiling height of 6 feet 8 inches (2032 mm) above a minimum area 30 inches (762 mm) by 30 inches (762 mm) at the showerhead.
