Table of Contents
Start by installing a new metal drip edge along the edge of the new overhang. You can then lay a course of new shingles along the lower edge. Work upward with the remaining courses until you reach the existing shingles. At this point, slip the final row of new shingles beneath the old shingle tabs.
How much does it cost to extend your roof?
It typically costs between $15,000 to $125,000 or more to raise a roof on your home. Get quotes from local contractors for the best estimate. Raising a roof is a significant investment that can dramatically increase living space in your home, improve or customize the way it looks and even prevent weather damage.
How do you extend a gable end roof overhang?
Attach fascia board at the edge of the overhang. Install roof deck sheathing extended over the gable framing and installed with correct fasteners and fastener pattern. Install a rigid soffit material such as structural sheathing plywood or OSB to cover the underside of the overhang.
How far can roof overhang without support?
Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external support.
What is roof overhang called?
Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed.
Can you build a roof over an existing roof?
When it’s time for a new roof you have a couple options to pick from, you can either remove the old roof or replace it with a new one. You can also build over your existing roof. Roofing requires a flat surface so the curled shingles will need to be removed.
Is it possible to raise the roof on a house?
You can still raise stick roofs, but it will most likely require you to tear down the existing roof and rebuild the structure. A few factors could make raising your roof impossible, or incredibly costly. These include: Your roof’s framing.
How do you Repitch a roof?
Pitched Roof Change the pitch on an existing sloped roof by removing the old roof and framing. Take off shingles or other roof covering and remove the membrane and sheathing. Use a pry bar to pull loose shingles and wood decking. Strip the roof to its rafters or trusses.
Can you extend roof rafters?
If your roof’s overhang is inadequate, you can extend the rafters to a degree, depending on the pitch of the roof. Extending the rafters with the existing roof sheathing in place is doable, but you will get better results if you add extensions during a complete reroofing project.
What is a rake overhang?
The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
How far can a cantilever roof extend?
According to the new span tables and IRC provisions, cantilevers can extend up to one-fourth the backspan of the joist. This means that joists, such as southern pine 2x10s at 16 inches on-center, spanning 12 feet are allowed to cantilever up to an additional 3 feet (see illustration, below).
How much overhang should roof shingles have?
Yes. Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
Do roofs need overhangs?
A roof overhang is an essential part of your roofing system to protect your house. If you are simply adding function and protection, or if you want to incorporate a new style to update the exterior of your home, a new roof overhang is a good idea.
How much should a rafter overhang?
Overhangs can vary from a few inches to a few feet depending on preference; however, the suggested width of an overhang is between 12” and 18” for eaves and no more than 8” for rakes. That said, overhangs can extend as far as 2′ without the need for external supports.
What is rake on roof?
Instead, the rake refers to the sloped sides of a gable style roof. This type of roof is one of the most common in colder or temperate climates, and consists of two roof sections sloping in opposite directions from the peak to allow for the best flow of precipitation off the roof.
How do you install rolled roofing over existing roofing?
Before you begin, thoroughly clean the existing roof, removing any debris like leaves or sticks. Then, install a layer of roofing felt to provide a sturdy base for the new roll roofing. Once this has been done, the roll roofing can be installed in the same manner as if it were over bare roof sheathing.
How do you join two roofs together?
How to Join the Roof Pitches? Step 1 – Preparing the Area. Step 2 – Measuring the Length of the Joined Area. Step 3 – Prepare a Piece of Flashing Material. Step 4 – Place the Flashing on the Meeting Point. Step 5 – Sealing the Edges of The Roof with Lumber. Step 6 – Apply a Bead of the Sealant Material.
