QA

Question: How To Repair Pressure Washers

How do I fix my pressure washer?

What is the most common problem with pressure washers?

Many pressure problems begin and end at the unloader. A cracked o-ring, dirt caught in the spring or a stuck shaft are the most common issues solved by simply removing the unloader and cleaning/looking for issues.

Why would a pressure washer stop working?

If your pressure washer starts and runs fine, but there’s no pressure or no water coming from the pump, it could be a clogged wand, hose or inlet filter. If not, you have a collapsed or kinked hose or a clogged wand. Both problems can most likely be fixed quickly without professional help.

Why is my pressure washer not spraying hard?

– Make sure your garden hose and high pressure hose are not kinked, leaking, or blocked in anyway and that the water is turned on full force and supplying the correct amount of water outlined in your owner’s manual. – Remove the water inlet filter and make sure it is free of debris. – Check the trigger gun and nozzles.

Why doesn’t my pressure washer have any pressure?

In general, the most common reason for a pressure washer not building pressure is that it is not getting enough water. This can be due to a hose problem, leakage, or blockage. Another reason can be air can get trapped inside the pressure washer pump or a problem with the nozzle.

How do you fix a pressure washer that won’t start?

When the pressure washer runs out of gas, then, the fuel pump overheats and needs to be replaced. You can try to get the pressure washer started again by removing the spark plug, putting about a tablespoon of gasoline or lighter fluid in the socket, replacing and reattaching the spark plug, and trying to start it.

What goes wrong with pressure washer pumps?

The two most common reasons behind the pressure washer pump going bad are a faulty unloader valve and a clogged carburetor (in the case of gas-powered washers).

Why does my power washer keep surging?

Why is my pressure washer surging? Water flow may be restricted to the pressure washer. Check that all hoses are free of kinks, leaks, or blockage. If the nozzle has even a little bit of dirt in the tip, it may cause enough obstruction for the pressure washer to pulsate.

Can I start a pressure washer without water?

Running the pressure washer without the water hose attached and the water turned on will cause the pump to run dry, damaging it. Don’t do that! It will burn out. The water is the coolant and it has to be flowing, not just on to cool properly.

Can you fix a pressure washer pump?

Before you can replace your pressure washer pump, you need to make sure you’ve chosen the correct replacement. Your new pump must be compatible with your pressure washer. You can’t replace your pump with any pump you wish, because they just won’t fit. Determine if your pressure washer uses an axial or triplex pump.

Why is my Simpson pressure washer not building pressure?

Your SIMPSON may be operating in low-pressure due to an incorrectly sized nozzle or a nozzle that has worn out. Always replace any worn or broken nozzles as they can potentially be a safety hazard. ALWAYS use accessories that are within your pressure washer’s PSI range.

Why is my electric pressure washer not turning on?

Why won’t my electric pressure washer start? Make sure that it is plugged directly into a wall outlet, has a tight connection and that your outlet can provide adequate grounded power to operate your pressure washer. If the motor has stopped but is making a humming sound, it is usually a faulty capacitor.

Why does my pressure washer keep starting and stopping?

The stalling of the engine of your electric pressure washer may be because of the bad unloader valve, which is due to the pressure inside the pump becoming greater than your engine’s power to rotate your pump.

How long does a pressure washer pump last?

Most low cost pressure washers are made with lower quality pumps. The life expectancy, of those pumps is around 60 to 100 hours of use. With higher quality pressure washers, the life expectancy of their pumps is closer to 500 hours. On average, households use their water pressure washer around 50 hours per year.

How long can you run a pressure washer?

You should not run a pressure washer (except professional equipment) for more than five minutes. While the duration may vary from model to model, it should be between 3 and 5 minutes. Leaving your pressure washer running for more than five minutes can result in overheating.

Do you need a pump for a pressure washer?

a belt driven or gear driven pressure washer will suck water from the tank on its own, no pump necessary. A direct drive machine will need to have a pump feeding it , which means you will need a generator to run the pump ( or a long extension cord).

What happens if unloader valve is bad?

A failed unloader valve can cause high pressure at the nozzle. The unloader valve recirculates water to the pump inlet when the pump is running but the spray wand isn’t in use. A defective pressure regulator can cause high pressure at the nozzle.

What are the symptoms of a bad unloader valve?

One of the most apparent problems with the unloader valve is less output pressure and a lower water flow. If the valve does not work correctly, the pressure washer pump will get hot, and more power is asked from the engine. If you have a gas pressure washer, you can hear more engine noise due to the higher load.